Activity Stream
-
Older Activity
-
9 Hours AgoThat looks off topic.22 replies | 2712 view(s)
-
11 Hours AgoThat's a choke. They help smooth/suppress noise from the motor. It's worth checking it's not failed and gone open circuit (either with a...13 replies | 373 view(s)
-
13 Hours AgoNo luck yet with the motor controller. It has 240v to it, I can measure 12v across pins 12 & 10. I attached a pot to 12 & 10 and 11 and can vary 11...13 replies | 373 view(s)
-
13 Hours Agohttps://t.me/pump_upp - best crypto pumps on telegram Make 1000% and more within 1 day, join channel @pump_upp !22 replies | 2712 view(s)
-
14 Hours Agonobby replied to a thread FOR SALE: three positec vrdm 564/50 motors 5 phase and a 3 axis 5 phase controller in Items For Sale3 motors no cables - i am using them on my new motors and drivers i could leave it all ready to run IF you vcan work out the inputs into the rs232...2 replies | 203 view(s)
-
16 Hours AgoBikerDaily replied to a thread WANTED: Dahlgren dsc2000 black box to drive Gryphon suregrave router in Items WantedRelayman So we are wondering if the fault with our system is the Dahlgreen. Could it be firmware? Or RAM memory? Our machine sometimes prints...10 replies | 6284 view(s)
-
16 Hours AgoJohnHaine replied to a thread NEW MEMBER: Trained monkey looking to level up! in New Member IntroductionsGood stuff, glad to help.14 replies | 1126 view(s)
-
17 Hours Agojohnsattuk replied to a thread FOR SALE: three positec vrdm 564/50 motors 5 phase and a 3 axis 5 phase controller in Items For SalePics of the three phase motors/controller ?2 replies | 203 view(s)
-
18 Hours AgoMammers replied to a thread NEW MEMBER: Trained monkey looking to level up! in New Member IntroductionsRecently just did this as per your and m_c's recommendation, couldn't be happier with how it worked out. Thanks so much.14 replies | 1126 view(s)
-
1 Day AgoHello Digger is this still available? cheers ste8 replies | 4555 view(s)
-
1 Day AgoFirst part is done and test fitted.22 replies | 5454 view(s)
-
1 Day AgoYou can connect a pot, which if you have one laying around (IIRC they're normally around 100k), I would wire up just to check the drive still works....13 replies | 373 view(s)
-
1 Day AgoI plugged the computer in and it immediately started popping and smoking! Suffice to say I think the BBC B is dead. I have a bit of time tomorrow so...13 replies | 373 view(s)
-
1 Day AgoUse an old phone charger with USB output, butcher a USB lead to get at the power conductors. Yes you MUST connect the earths. Probe is specced for...18 replies | 851 view(s)
-
1 Day AgoThat's the early system. The spindle drive board (in your first picture post), should have everything marked on it. As it's a NEControl, I'm not...13 replies | 373 view(s)
-
1 Day Agonobby replied to a thread WANTED: three nema 23's with 8 wires - 41mm or 57mm dont care in Items Wantedhello i just bought six of those 8 wire nema 23's on ebay 7 quid each thanks I dont understand the 5 phase stuff so I have three of those motors...2 replies | 188 view(s)
-
1 Day AgoJust be looking at IRLZ34N online John, looks like a great solution. Just not sure how I power the probe, does it need to be from the Gecko's 48v...18 replies | 851 view(s)
-
1 Day Agojohnsattuk replied to a thread WANTED: three nema 23's with 8 wires - 41mm or 57mm dont care in Items WantedNot what your asking for, but have some Vexta PK566 5phase motors and a dual shaft PK5642 replies | 188 view(s)
-
13 replies | 373 view(s)
-
13 replies | 373 view(s)
-
13 replies | 373 view(s)
-
13 replies | 373 view(s)
-
13 replies | 373 view(s)
-
1 Day AgoTHanks, How do I go about using the original spindle drive? I believe it was controlled by the computer and not sure what I need to do on the...13 replies | 373 view(s)
-
1 Day AgoThat's really interesting, I've never heard of GRBL. The amount of open-source stuff out there genuinely boggles my mind sometimes. What a time to be...17 replies | 1148 view(s)
-
1 Day AgoI grew up before Windows - an Amstrad PC1640 - I had a lot of fun getting a plotter working on that. I like LPT ports, there again I like Victorian...17 replies | 1148 view(s)
Homing Y/A Axis Says Limit Switch...