Activity Stream
-
Older Activity
-
2 Hours AgoAccTek China replied to a thread CNC Horizontal gang style lathe in Lathes, Lathe Rebuilding & ConversionsWhat kind of lathe do you want to build, or what do you plan to use for this lathe?1 replies | 157 view(s)
-
3 Hours AgoKitwn replied to a thread Further Progress with my JazzCNC .. Guitar Body in Woodworking Project ShowcaseI didn't realise you'd copied my design! Just dont go hawking your strange ideas on the forum. Kit7 replies | 463 view(s)
-
9 Hours Agook i nearing the end of my build and got thinking. i have 3 Nema 17 Stepper Motor 1.7A 0.59 Nm 84oz.in also a spare Nema 23 Stepper Motor 2 phase...0 replies | 77 view(s)
-
9 Hours AgoI search for a collet or costum spindle for the Roland camm3 Pnc 3000 or somebody, which could make me one. I have the drawings for them. Should be...0 replies | 5 view(s)
-
9 Hours AgoHey, I'm a young guy from germany. My english is quite bad, sorry for that. I bought a Roland Camm3 PNC3000 last weekend, since then i was...0 replies | 3 view(s)
-
10 Hours AgoDumpling replied to a thread £4.95 Screw Rod, SFU1605 1000mm, is it really any good in General Discussioncame it cost 5 pound and well works fine when i did a mock up, better than the 13 pound t8 lead screw they sell. got 4 now. cant get a burger king...13 replies | 800 view(s)
-
10 Hours AgoDumpling replied to a thread £4.95 Screw Rod, SFU1605 1000mm, is it really any good in General Discussionit came it cost 5 pound and well works fine when i did a mock up, better than the 13 pound t8 lead screw they sell. got 4 now. cant get a burger...13 replies | 800 view(s)
-
12 Hours AgoThat looks like it's a bit more than just a NVR switch. The circuit board looks like it's got some kind of speed controller and/or soft start built...6 replies | 161 view(s)
-
14 Hours AgoThose terminals look like just two terminals with two tags on each. Look carefully at where they are rivetted into the top cap - they are probably a...6 replies | 161 view(s)
-
15 Hours AgoWasnt immediately aware of anythying but wasnt listening out for any humming. I'll try it out to it tomorrow when back in the workshop6 replies | 161 view(s)
-
15 Hours AgoJAZZCNC replied to a thread Further Progress with my JazzCNC .. Guitar Body in Woodworking Project ShowcaseIs that C5 or C3 string theory.? we don't want any backlash...:whistle:7 replies | 463 view(s)
-
15 Hours AgoThanks guys, Think I might avoid the manual startup haha! I wondered about the cap as well so I bought a spare of the same value. I see my...6 replies | 161 view(s)
-
16 Hours AgoNeale replied to a thread Further Progress with my JazzCNC .. Guitar Body in Woodworking Project ShowcaseI'm more into string theory. At least, that's how bits of my router are held on...7 replies | 463 view(s)
-
16 Hours AgoI'm with Clive - my first port of call would be the starting capacitor. It's not that unusual for one of these to fail and you've pretty much...6 replies | 161 view(s)
-
16 Hours AgoNo, they are the worst coupling to use. you are better using an Oldham-type coupling like this. http://www.fbtmotion.com/html/16.html Or better...1 replies | 153 view(s)
-
16 Hours AgoDoes the motor hum if so it could be the capacitor6 replies | 161 view(s)
-
18 Hours AgoHi there, I bought an old Klinger & Born (Elekra Beckum) table saw with what was described as having a faulty on/off switch. Right enough it...6 replies | 161 view(s)
-
19 Hours AgoHi! I’m unsure of what couplings to use. As it seems I will go with alu couplings with a slit in them. Any thoughts about that? I’ve noticed...1 replies | 153 view(s)
-
22 Hours Agocropwell replied to a thread Further Progress with my JazzCNC .. Guitar Body in Woodworking Project ShowcasePlease do not warp the Space-Time Continuum on your journey.7 replies | 463 view(s)
-
1 Day AgoSo will continue the thread over there Clive .Will zip and post everything I can.8 replies | 317 view(s)
-
1 Day AgoJohn. There are more people that use Linuxcnc on the other forum Andy Pugh on there is very knowledgeable. You have to remember that none of us...8 replies | 317 view(s)
-
1 Day AgoHello, I am also interested in the manual. I would be very happy to receive a copy. Many thanks in advance.10 replies | 5346 view(s)
-
1 Day AgoHi Clive and thanks for your input. When I first asked the question on both forums , I was unaware that the same faces would respond on both. Sorry...8 replies | 317 view(s)
-
1 Day AgoI bought a 4th rotary axis, which I am not sure if I should be happy about on a "you get what you pay for" basis or should have received something...0 replies | 182 view(s)
-
1 Day AgoEasy answer to the sensor question: 1 sensor gives speed. 2 sensors gives speed and direction 3 sensors gives that and an index pulse (absolute...8 replies | 317 view(s)
-
1 Day AgoI see that you have also posted on the linuxcnc forum. Once you have used stepconf then you have to hand edit the files as stepconf will overwrite...8 replies | 317 view(s)
-
1 Day AgoWell, not exactly correct, we set it up UCCNC before you took the machine so the pendants can be added at a later date if required. This is why it...97 replies | 16775 view(s)
-
1 Day AgoI am not sure what gmocappy needs in the way of "at speed " signal . I know I do not have the ratio correct in that a call for S300 would give me a...8 replies | 317 view(s)
-
2 Days AgoI'm with Clive on this one (standing on the shoulders of the LInuxCNC giant :). - check that gmocappy needs or doesn't need a spindle-at-speed...8 replies | 317 view(s)
-
2 Days AgoThe pendant is plug and play. Dongle in a usb slot and hey presto it works like a charm. Touch off plate and spanner’s came with the machine97 replies | 16775 view(s)
CNC Horizontal gang style lathe