Activity Stream
-
Older Activity
-
3 Hours AgoWell, you are in a funny place with this machine and heading on a potentially slippery slope.? There is no easy way to say this so I'll just say it.!...2 replies | 116 view(s)
-
5 Hours AgoOK good to know thank you339 replies | 272360 view(s)
-
14 Hours AgoWelcome to the forum Anthony. Somebody in the know will hopefully be along to help you. Meantime I'm keeping my tinfoil hat on ;-)2 replies | 116 view(s)
-
15 Hours AgoThose water filters will take 8 bar it will probably say that on the box and the little screw on RH side is for letting the air out (priming) when...339 replies | 272360 view(s)
-
1 Day AgoSince I have an air compressor . . . I decided it was about time !339 replies | 272360 view(s)
-
2 Days AgoJust use the widest cutter you have and write a bit of code to make test cuts for both directions on a piece of scrap then adjust as required,...1 replies | 216 view(s)
-
2 Days AgoThanks for the heads up guys! I'll be using the UC300ETH-Max, (UB-1+UD-1). I'm retrofitting an older machine, and want to keep the performance....12 replies | 9353 view(s)
-
2 Days AgoIs there any easy cheap way to tram the nod on a workbee other than paying over £100 for a gauge1 replies | 216 view(s)
-
2 Days AgoHi All, I am new here and a hobby table top CNC user. I have the FoxAlien CNC-4040-Basic, this comes with a 60w motor. I am looking to upgrade...2 replies | 116 view(s)
-
2 Days AgoHi all, my name is Tad Brabham and I have a Boxford TCL 125 which I am converting to MACH3. I'm new to all this and may need some help0 replies | 71 view(s)
-
3 Days AgoNice work. The rigidity of the machine is really showing on the surface finish.19 replies | 19007 view(s)
-
3 Days AgoHi, I have found that the DOS software runs very well in the latest version of DosBox X which is free online. My conect cadet plus runs from an...50 replies | 67433 view(s)
-
3 Days AgoHi Andrew, I've been using this: Sign Mask Signmask Spandex Avery Dennison Light Blue 380mm EU 54876 A Print Sign Works well, cant use solvent...1 replies | 351 view(s)
-
3 Days AgoTo me it looks like you are going to slow with the feed rate1 replies | 175 view(s)
-
3 Days AgoHelp I am surfacing some Ash across grain and its burning, bit is 28.5 Amana 16000rpm stepover 40% speed rate 35 inch per min. Only used the amana...1 replies | 175 view(s)
-
3 Days Agojust bought 1 today hopefuly il get this software up and running thanks guys for your sw and info its greatly appreciated50 replies | 67433 view(s)
-
4 Days AgoJAZZCNC replied to a thread How to setup Chinese AASD Servo electronic gearing in Machine DiscussionDazp suggests a good board because the UB1 is an excellent choice if you are using servos due to the fact its differential line drivers are nice and...12 replies | 9353 view(s)
-
4 Days AgoOK, but how do you expect us to give you meaningful help if you are showing pics that don't match how you have it set up.? My suggestion is that...5 replies | 343 view(s)
-
4 Days AgoI have a cut off saw, but the rotary switch broke whilst in transit. Here is the plate from the motor. There are 6 connections on it U1/V1/W1...0 replies | 139 view(s)
-
4 Days AgoAre you sure the drives are enabled?. Are you sure about the pin numbers?.5 replies | 343 view(s)
-
4 Days AgoHere are some test cuts and accuracy. I am quite happy with the outcome. https://www.youtube.com/watch?v=1ZTpCh8eap4&t=3s19 replies | 19007 view(s)
-
4 Days Agodazp1976 replied to a thread How to setup Chinese AASD Servo electronic gearing in Machine DiscussionYep. You want your step/dir signals wired differential. Using the open collector way like you would with steppers is no use. I was told OC is...12 replies | 9353 view(s)
-
4 Days AgoHi CNCConnect sorry i should have been a bit clearer in my last post, to calculate motor loading the weight of the gantry needs to be known, also...4 replies | 677 view(s)
-
4 Days AgoThe pic is older, I changed it to port #3 and I have read and done what I understand from the manual.5 replies | 343 view(s)
-
4 Days AgoThat was an old pic I put it on port #3.Have read the manual and done everything I understand from it.5 replies | 343 view(s)
-
5 Days AgoJazz answered your question perfectly. But I'll answer with another question. How are you going to interface the UC300eth with the servo? The thought...12 replies | 9353 view(s)
-
5 Days AgoJAZZCNC replied to a thread How to setup Chinese AASD Servo electronic gearing in Machine DiscussionThe 400Khz is per axis output.12 replies | 9353 view(s)
-
5 Days AgoProbably because you are using the wrong Port.? Port #1 which you are using is mostly Inputs, Port #2 and #3 are the ones with all the outputs on...5 replies | 343 view(s)
Help, FoxAlien motor upgrade