Activity Stream
-
Older Activity
-
5 Hours AgoDavantech started a thread Opinions on Integrating Robots for Part Handling in CNC Machining? in Metalwork DiscussionHey everyone, I've been pondering over the idea of using robots in CNC machining processes to handle the placement of parts into the machine and...0 replies | 38 view(s)
-
9 Hours AgoA_Camera replied to a thread Is a 600W AC servo better than a matching asyncrounous single phase AC motor? in Machine DiscussionYes, I know that, but normally the higher the power the higher the torque at the same speed. Also, the pulleys are as they are, the question was more...4 replies | 274 view(s)
-
16 Hours Agoveres replied to a thread custom 3d models for CNC, sculpture, portraits, reliefs in Opportunities Available & Sought3D bas-relief of Hercules. You can view it in a larger resolution on my website80 replies | 228990 view(s)
-
16 Hours AgoJohnHaine replied to a thread Is a 600W AC servo better than a matching asyncrounous single phase AC motor? in Machine DiscussionYou might be confusing power and torque. Using a large diameter holesaw really needs quite high torque but probably not much power. The ideal is a...4 replies | 274 view(s)
-
20 Hours AgoA_Camera replied to a thread Is a 600W AC servo better than a matching asyncrounous single phase AC motor? in Machine DiscussionThank you. Yes, I am concerned about the power because I don't want to just drill, but also use hole saws of large sizes in thick steel. My current...4 replies | 274 view(s)
-
1 Day AgoFor sale: MESA 7i92TH Anything I/O Ethernet card MESA 7i76 STEP DIR I/O daughtercard - sourcing output version DB25F-IDC26 cable adaptor ...0 replies | 137 view(s)
-
1 Day AgoJohnHaine replied to a thread Is a 600W AC servo better than a matching asyncrounous single phase AC motor? in Machine DiscussionInduction motors have quite large diameter rotors and substantial stators so they are quite large. The "heatsink" doesn't contribute much in size. ...4 replies | 274 view(s)
-
1 Day Agom.marino replied to a thread BUILD LOG: My Build - I blame you lot for this....! in DIY Router Build LogsNice playground. Glad to see you back and hope you are doing well.155 replies | 154327 view(s)
-
2 Days AgoHi Bladevane, please send me the old eMachineShop 1.932, 1.935 My email is: tsps at mail.com Thanks, John170 replies | 168837 view(s)
-
2 Days AgoI can't remember if I went 1kw or 1.25kw servo on mine. I was always going to program the servo drive to run above the rated speed, but that's still...6 replies | 463 view(s)
-
2 Days AgoI put a 1.5KW Panasonic Servo on my Previous Triac as the DC motor was failing. You can gear accordingly.6 replies | 463 view(s)
-
3 Days AgoTheGoodGuy started a thread FOR SALE: ColdEND32 Mistless Coolant Sprayer (like FogBuster) in Items For SaleI am selling a new, unused mistless coolant sprayer ColdEND32 als Komplettbausatz - Minimalmengenschmierung. The price is €350. More...0 replies | 211 view(s)
-
3 Days AgoA_Camera started a thread Is a 600W AC servo better than a matching asyncrounous single phase AC motor? in Machine DiscussionTypically, a servo motor has 30%-60% higher torque capacity and 30% better torque utilization with faster acceleration and deceleration, compared to...4 replies | 274 view(s)
-
3 Days AgoI decided to make an upgrade (actually more than one...) of my CNA lathe. Number one update is to change the spindle motor. While the...33 replies | 46560 view(s)
-
3 Days AgoAlmost finished the enclosure . . . .101 replies | 164798 view(s)
-
5 Days AgoJohnHaine replied to a thread TOSHIBA VF-NC3S VFD for sale (unused) in Classified Ads, Buy, Sell & SwapAnother method of reforming which I have used successfully is to connect a variac (variable transformer) to the normal mains input, switch on, and...3 replies | 2532 view(s)
-
5 Days Agomekanik replied to a thread TOSHIBA VF-NC3S VFD for sale (unused) in Classified Ads, Buy, Sell & SwapJust having a tidy up and found this3 replies | 2532 view(s)
-
6 Days AgoI would buy a power line adapter and bring WiFi to your shed. Has worked for me and more reliable than range extenders. Plenty of them in Argos ...3 replies | 420 view(s)
-
1 Week AgoLet me guess, you have your WiFi router in the house connected to the incoming copper line. As well as the cnc machine you are using a computer, ...3 replies | 420 view(s)
-
1 Week AgoWelcome to MYCNCUK.3 replies | 420 view(s)
-
1 Week AgoPulley is 18 tooth, L tooth size/profile (it's imperial - 3/8" pitch IIRC), and 1" wide. Belt is 15" long. I do have a F360 model of the Triac...6 replies | 463 view(s)
-
1 Week AgoFor sale is this Denford 2600 Pro CNC Router. I own it, but it is based at a school in Dorset. These are lovely machines and I have used it...0 replies | 289 view(s)
-
1 Week Agoim trying to work out what exact pulley the existing motor has on it without stripping the head. i found some old photos. can anyone tell me what...6 replies | 463 view(s)
-
1 Week AgoI believe they did a 4k and 6k version only. Id probably just leave the current spindle bearings as is and replace I'm due course if I needed to.6 replies | 463 view(s)
-
1 Week AgoFirst thought is whether the current spindle bearings (and maybe oil seals?) could take that speed. Are there high-speed Triacs? I can understand...6 replies | 463 view(s)
-
1 Week Agoim looking at the idea of changing the spindle motor on my triac, mine currently has a 4k rpm spindle. it would be nice to have a minimum of...6 replies | 463 view(s)
-
1 Week AgoHi I’m Ron, I’ve recently bought an oozenest workbee, used. I have it set up in a cabin at the bottom of my garden. The machine I bought is operated...3 replies | 420 view(s)
-
1 Week AgoHaha, ye i thought someone might say that. Could be a can of worms2 replies | 1221 view(s)
-
1 Week AgoLeave well alone IMHO.2 replies | 1221 view(s)
-
1 Week AgoIm looking at this unfinished conversion. (half the NZ dollars to get pounds) What do you think ? ...2 replies | 1221 view(s)
Opinions on Integrating Robots for...