Activity Stream
-
Older Activity
-
1 Hour AgoHiltonSteve replied to a thread BUILD LOG: My Build - I blame you lot for this....! in DIY Router Build LogsOh, the reason I've not been on here much is because I've been busy in my new playground for the last few years... Don't all shout at once but...154 replies | 150196 view(s)
-
1 Hour AgoGot a few bits of aluminium extrusion that I don't need... If anyone is interested let me know and I will see what i can do. Various sizes -...0 replies | 16 view(s)
-
2 Hours AgoHiltonSteve replied to a thread BUILD LOG: My Build - I blame you lot for this....! in DIY Router Build LogsMorning all.... Its been a while but I'm back again, and another divorce just sorted out..! Don't take the piss too much...! How is everyone??154 replies | 150196 view(s)
-
2 Hours AgoJohnHaine replied to a thread Please help identify these CNC machines found at my school. (should make PCBs) in General DiscussionThat could equally be an asset number, for example. If nearly 4000 units were made they would be better known. Can you take photo 1 again with...4 replies | 134 view(s)
-
2 Hours Agochazzy2501 replied to a thread Please help identify these CNC machines found at my school. (should make PCBs) in General Discussionit does have a serial number in the thousands 00003882 or something. (hand written)4 replies | 134 view(s)
-
3 Hours AgoJohnHaine replied to a thread Please help identify these CNC machines found at my school. (should make PCBs) in General DiscussionThat does not look like a commercial product but something made as a prototype in a lab.4 replies | 134 view(s)
-
15 Hours Agoroutercnc replied to a thread Please help identify these CNC machines found at my school. (should make PCBs) in General DiscussionOK flipped them around for you. Could be well off track here but a small enclosed machine for education makes me think Denford / Denford...4 replies | 134 view(s)
-
1 Day Agochazzy2501 started a thread Please help identify these CNC machines found at my school. (should make PCBs) in General Discussion2 of these have been found in a cupboard here at the school, with a new belt I think they can work again. (I've been here since 2005 and never seen...4 replies | 134 view(s)
-
1 Day AgoHi Neale, I will try what you have suggested, seems to be the right way to go. Ooznest has been good but I think there is a communication breakdown....5 replies | 271 view(s)
-
2 Days AgoAs a quick sanity check, have you tried comparing cable colours between each of the axes? There is always the possibility that a cable connector is...5 replies | 271 view(s)
-
2 Days AgoLooked at that link, and will try that as a last resort but ty for it, really appreciate it5 replies | 271 view(s)
-
2 Days AgoJust done a little bit of research. Looks like the Ooznest relies on prewired harnesses and a bunch of configuration files to set machine parameters....5 replies | 271 view(s)
-
2 Days AgoTwo points to note before I suggest something: - I don't know the Ooznest hardware kit at all, so not sure how the stepper motor to driver...5 replies | 271 view(s)
-
2 Days AgoHi all, I am completely new to everything related to the CNC world, having said that I have had a machine sitting in their boxes for some time now...5 replies | 271 view(s)
-
2 Days AgoWelcome to MYCNCUK.1 replies | 290 view(s)
-
2 Days AgoHi all, Thank you for allowing me to join this forum, My name is Mark and I live in a small village called Alfriston in East Sussex. I retired from...1 replies | 290 view(s)
-
3 Days AgoStarting the enclosure for the knee lift electronics. I seem to like making it complicated!100 replies | 159202 view(s)
-
6 Days AgoWhat are you struggling with?4 replies | 734 view(s)
-
6 Days AgoJohnHaine replied to a thread NEW MEMBER: Denford Triac converted to UCCNC in New Member Introductions...or there!4 replies | 734 view(s)
-
6 Days AgoJohnHaine replied to a thread NEW MEMBER: Denford Triac converted to UCCNC in New Member Introductionshttps://www.forum.cncdrive.com/ Maybe more likely to find help here.4 replies | 734 view(s)
-
6 Days AgoBeen using my home built cnc mill router for years now for personal use. Its getting a bit worn and after being shipped with our belongings from...0 replies | 445 view(s)
-
6 Days AgoI am looking for a little guidance on how to test my 3 phase spindle with a multimeter to see if there is an issue ,,, as it won't run ,just a slight...0 replies | 537 view(s)
-
1 Week AgoAhmad T replied to a thread NEW MEMBER: Denford Triac converted to UCCNC in New Member IntroductionsWelcome to the forum.4 replies | 734 view(s)
-
1 Week AgoHi All, Looking for some assistance to set up my Triac that I have had retro-fitted with UCCNC software. Any assistance would be much appreciated...4 replies | 734 view(s)
-
1 Week AgoPhil Mayor replied to a thread Testing The VFD, Break Resistor and Wiring to AXBBE in Spindles & Drive MotorsI think I'm going to try to return this VFD, I do think it's quite a good bit of kit, it's just the Chinglish that makes this a much harder job, I've...30 replies | 4899 view(s)
-
1 Week AgoI am running a fuling vfd which until today was fine , the spindle would not operate , trying to start but won't, i then noticed the spindle hz...0 replies | 489 view(s)
-
1 Week AgoPJMCAmbs started a thread FOR SALE: JET 22-44 Plus Drum Sander 240 Volt Axminster with Auto Feed in/Feed out Table. in Items For SaleIntroducing the JET 22-44 Plus Drum Sander, the perfect solution for all your woodworking needs. This high-quality sander boasts a powerful 240 Volt...0 replies | 619 view(s)
-
1 Week Agovoyager1972 replied to a thread touch probe connectivity with ceramic bearings in Machine DiscussionThanks for the reply , that makes things a lot clearer to me now , they operate different from a touch plate.12 replies | 1487 view(s)
-
1 Week AgoThe product description says: "Normally closed specification technical parameters Output mode: BNC (normally closed)" Which implies that it...12 replies | 1487 view(s)
My Build - I blame you lot for...