Activity Stream
-
Older Activity
-
4 Hours AgoGracias por responder. Mi correo es [email protected] soy de argentina, de dónde eres tú?12 replies | 8487 view(s)
-
5 Hours AgoJohnHaine replied to a thread Wiring plan for upgrading my chinese cnc electrics enclosure, have I missed anything? in Gantry/Router Machines & BuildingOn my lathe the e-stop turns off the drive and raises an E-stop condition on the controller. This halt execution but the drives remain energised and...3 replies | 55 view(s)
-
5 Hours Agopaul4523 replied to a thread Wiring plan for upgrading my chinese cnc electrics enclosure, have I missed anything? in Gantry/Router Machines & BuildingThe latching stop and start buttons are to turn on and off the VFD and Drives. From what I've seen this seems to be a common setup. You are correct...3 replies | 55 view(s)
-
5 Hours AgoJohnHaine replied to a thread Wiring plan for upgrading my chinese cnc electrics enclosure, have I missed anything? in Gantry/Router Machines & BuildingWhat's the reason for the stop/start button? Is it actually the E-stop? Normally it's useful to keep the stepper drives powered up even in an...3 replies | 55 view(s)
-
7 Hours Agopaul4523 started a thread Wiring plan for upgrading my chinese cnc electrics enclosure, have I missed anything? in Gantry/Router Machines & BuildingUpgrading my OMIO X4 machine to an AXBB-E controller and new enclosure. I'm a novice and have tried to learn as much as possible in order to take on...3 replies | 55 view(s)
-
8 Hours Agohttps://www.amazon.co.uk/Breakout-Controller-Control-Engraving-15-32VDC/dp/B084GPP44J/ref=sr_1_5?crid=1893MVWCXEGBZ&dib=eyJ2IjoiMSJ9.Lvwp1QoEu02_DVMHD...2 replies | 124 view(s)
-
17 Hours AgoDean may have some controllers. http://www.jazzcnc.co.uk/2 replies | 124 view(s)
-
23 Hours AgoHello It has been a couple of years since I built my lathe and mill, and have picked up another lathe recently to convert. A lot seems to have...2 replies | 124 view(s)
-
1 Day AgoMi mail es [email protected] soy de argentina, de dónde eres tú? Translation - Lee My email is [email protected] I'm from Argentina, where are you...12 replies | 8487 view(s)
-
1 Day AgoHello good. I would be having the same problem as JGC ARG. I lost the toolpath software for Windows 95/98 version 2.6. Is it possible to share the...12 replies | 8487 view(s)
-
2 Days AgoI don't think I ever received your email in a DM. Hit me up if you still want it and I'll share the Dropbox folder with you. K12 replies | 8487 view(s)
-
2 Days AgoIf you send me your email address I can send you what I have which is hopefully what you need. K12 replies | 8487 view(s)
-
2 Days AgoHola soy nuevo en el foro, se me ha roto la pc y he perdido el software toolpath for Windows 95/98 versión 2,6 para hacer funcionar el router axyz...12 replies | 8487 view(s)
-
5 Days AgoWell here we are, the last episode in the drill press upgrade series . . . . . probably.105 replies | 189568 view(s)
-
1 Week AgoI just bought and it's really good 300 on Amazon if you apply the voucher Printing now at 600mm/s with no issues, super nice quality A...0 replies | 901 view(s)
-
1 Week AgoHi, is the SW dongle still available Regards, Theo3 replies | 14788 view(s)
-
1 Week AgoHire somebody with a laser scanner.they will be done in half a day or so and can then provide you with a file,or series of files that will be...2 replies | 976 view(s)
-
1 Week AgoI understand that kitchen fitters use a laser scanner device to digitise the rooms where for example new worktops and units are to be fitted, and...2 replies | 976 view(s)
-
1 Week AgoHey Folks, I'd like to rip out the interior of a boat and refit it utilising the CNC for all the woodwork. Ideally I'd like to CAD it out...2 replies | 976 view(s)
-
2 Weeks AgoGood advice as expected. Many thanks I'll check the outputs and adjust the speed down to a lower value. It can't hurt to give it a try....29 replies | 25914 view(s)
-
2 Weeks AgoFor the video above some people have shown an interest in the code so here it is in a zip file. This will open in most text readers if you only want...105 replies | 189568 view(s)
-
2 Weeks AgoUpdating the software . . . plus more hardware issues found!105 replies | 189568 view(s)
-
3 Weeks AgoWhat are the terminal numbers on the VFD that the wires are connected to? Green will be X1, which is an input, and I'd guess is used to switch the...3 replies | 4935 view(s)
-
3 Weeks AgoNovamill switches, on my mill anyway, are standard microswitches. Maybe there's a wire dropped off the z switch? If you are seeing the lights...29 replies | 25914 view(s)
-
3 Weeks AgoSo a long awaited update on my Novamill situation. The day after my last post I took a call from Brian at CNC4U, where he made some suggestions to...29 replies | 25914 view(s)
-
3 Weeks AgoHi guys, I've taken the advise of m_c and added an USB controlled breakout board and an extra 24VDC power supply. Tried to hook it up and got the...3 replies | 4935 view(s)
-
4 Weeks AgoAfter sorting out some electrical issues the enclosure is finally working!105 replies | 189568 view(s)
-
4 Weeks Agohttps://www.ebay.co.uk/itm/166758284969 I'm happy to answer any questions. This is complete with safety hood, stepper and spindle drive...0 replies | 3270 view(s)
-
4 Weeks AgoIf you're looking to jump straight into anodizing aluminum without the hassle of trial and error, I found a guide that’s pretty straightforward and...84 replies | 124681 view(s)
AXYZ RS485 wiring.