Activity Stream
-
Older Activity
-
8 Hours AgoHi There are plenty of suppliers of industrial brush strip in the UK ...10 replies | 14433 view(s)
-
9 Hours AgoI was thinking of these for a situation where you're clamping down on the axis of the adjuster (e.g. like the Z-axis alignment on @routercnc's...2 replies | 57 view(s)
-
9 Hours AgoIf they're only for alignment purposes, standard M4 or M5 will do the job just as well, and be far cheaper. Or an original fine adjusting tool...2 replies | 57 view(s)
-
10 Hours AgoI'm talking to a manufacturer who makes these things about getting some M10x0.75x12mm flat end grub screws to be used in tramming/tweaking on my...2 replies | 57 view(s)
-
11 Hours AgoHow about this on ebay? https://rover.ebay.com/rover/0/0/0?mpre=https%3A%2F%2Fwww.ebay.co.uk%2Fulk%2Fitm%2F323692003138 Sent from my BBB100-2...10 replies | 14433 view(s)
-
15 Hours Agono probs. i'll check back tomorrow3 replies | 171 view(s)
-
16 Hours AgoWhat are you using when the code for circles isn't OK?3 replies | 197 view(s)
-
17 Hours Agostudio45uk replied to a thread Looking for advice on converting driver on Boxford CNC Router to Mach3/4 in Boxford RoutersHi guys, I have an older model A3HSR non-USB machine, now running with a Windows XP controller PC. I'd like to convert it to use Mach3, and...7 replies | 1350 view(s)
-
18 Hours AgoHi. I'll make a video tomorrow to upload on Youtube. Should be better I think. Thanks for your reply!3 replies | 171 view(s)
-
18 Hours AgoHi. I use 810d controls so if you can post a pic of you work offset screen I can compare with my machine and see where it is going wrong3 replies | 171 view(s)
-
19 Hours AgoCool. I hope you get it up working as it should.20 replies | 10192 view(s)
-
20 Hours Agohi, no its only circles. Its a Mach3 thing which needs sorting. I have been told that if I put G91.1 in a line below G90 in the g code it will work...3 replies | 197 view(s)
-
20 Hours AgoTry a square and a rectangle too and report back. If they are all 2.2 times too big it's likely your step settings are incorrect and you will be...3 replies | 197 view(s)
-
21 Hours AgoI am from Somerset West, a town near Cape Town in South Africa. I own a Tormach PCNC770 cnc mill. I have also converted an Optimum BF20 mill to cnc...0 replies | 76 view(s)
-
22 Hours AgoHi, Welcome. I hope you find what you are looking for? perhaps some photos of your efforts so far!1 replies | 181 view(s)
-
23 Hours AgoLee Roberts replied to a thread Monitor doesn't connect to the dell desktop with Windows XP. in Computer HardwareGreat stuff, really pleased you got it sorted and thanks for letting us know! I think moving everything cnc related to a new box was a good idea,...9 replies | 362 view(s)
-
1 Day AgoEkfer replied to a thread Monitor doesn't connect to the dell desktop with Windows XP. in Computer HardwareGentlemen: I'm profoundly thankful. I followed your instructions and proceded to troubleshoot each component until I found that one of the two memory...9 replies | 362 view(s)
-
1 Day AgoOK so yesterday I managed to take some measurements for the X and Y stiffness of the new Atlas Mk4 machine. The machine was positioned so the...322 replies | 94281 view(s)
-
1 Day AgoWell 542 will be a step up from TB boards and 50V gives a fair performance. Next step up is 80V and lots of builds end up here but you would need...3 replies | 353 view(s)
-
1 Day AgoDoddy replied to a thread NEW MEMBER: Long time lurker, first time poster. in New Member IntroductionsNot by design, and not to any advantage for me, but I replaced the Z axis on a small Starmill with a plate driven on linear rails, and the wipers...1 replies | 161 view(s)
-
1 Day AgoHi all, I'm very new in the industrial CNC so I have a problem which probably will sound funny for more of you but I've spend lots of time to find...3 replies | 171 view(s)
-
1 Day AgoHi everyone I’m an engineering student in Switzerland with an interest in CNC machines. So far I’ve built one small machine (Chinese XY Table and...1 replies | 161 view(s)
-
1 Day AgoThanks Nick, I am looking for something that can work on slightly bigger jobs so Triac VMC etc. Sorry I should have stated this at the start. Again...7 replies | 752 view(s)
-
1 Day AgoHi, I have got a Denford Starmill with 3 position toolchanger that I am looking to sell. As original with Denford software and PC. Straight out of a...7 replies | 752 view(s)
-
2 Days AgoI joined this group to see what others are doing with cnc machines. I have built a few cnc machines, currently working on a laser cutter/engraver. ...1 replies | 181 view(s)
-
2 Days AgoI'm glad to be able to join this forum. I am still trying to design my CNC router. Planning on steel welded construction but there are so many...0 replies | 167 view(s)
-
2 Days AgoThe machine was homemade, it's a router and I really only intended to use it for woods and plastic machining (no metals). It's about 4 feet by 2...3 replies | 353 view(s)
-
2 Days AgoI'm using the 2010 Screenset so the original Mach script editor doesn't work with the 2010 set. I have however found a way to change the DRO no. to...20 replies | 10192 view(s)
-
2 Days AgoLegend! Thankyou - Your forum searching foo is far superior to mine ;)22 replies | 4199 view(s)
Diy dust shoe dust strip bristles
8 Hours Ago in Dust Extraction & Collection