Activity Stream
-
Older Activity
-
4 Hours AgoGnord replied to a thread FOR SALE: FOR SALE ShaperOrigin Handheld CNC Router W/Festool Spindle & Systainer in Items For SaleHey, I’d still be interested unless you’ve sold it already. Have you had it running though? If not I could bring up a transformer to test. G7 replies | 820 view(s)
-
5 Hours AgoThanks for the link to that very interesting paper John, it confirms many design principles I would love to implement - oh that someone would gift me...6 replies | 258 view(s)
-
5 Hours AgoOllie78 replied to a thread NEW MEMBER: About to fall down the rabbit hole ?? in New Member IntroductionsHello CNC people. I have made finally made some small progress with my machine, however it is a case of two steps forward one step back. After...20 replies | 3779 view(s)
-
8 Hours AgoNo probs mate. Glad to be of help11 replies | 458 view(s)
-
10 Hours AgoHi John, All problems are sorted out :) I didn't find how to reset the Base work offset but just uninstall/reinstall the software. Now all works...11 replies | 458 view(s)
-
12 Hours AgoChrisF Tecdur started a thread Replacement CNC Vision Panels (Tecdur® MachineSafe) in Manufacturer NewsHello all, For many of you with CNCs/Lathes etc, you will be keenly aware that the vision panels on your machines amass dirt and damage over time!...0 replies | 56 view(s)
-
15 Hours AgoHi If you are going to set a machine up using jack screws the frame members will end up only touching at a few points, while this may achieve...6 replies | 258 view(s)
-
17 Hours AgoWell done. A 5.5 KW Teknomotor will work well. I use a 6.8 KW HSD spindle (very similar) for aluminium (and could do wood etc) - just tune your...1 replies | 140 view(s)
-
17 Hours AgoLloyd Barnes replied to a thread Help with Mach 3 - Cant get the motors to respond in General ElectronicsHi Doddy Thanks for taking the time to reply. I found the problem about 2am last night. Its down to the fact that I'm an idiot (not...2 replies | 131 view(s)
-
19 Hours AgoOne possibility is the new PC's parallel port being a low-voltage variant (3.3V rather than 5V) - take a DVM and measure the pin voltages on the...2 replies | 131 view(s)
-
1 Day AgoMy journey began quite a while ago with me being asked to produce curved panels for various projects in the workshop. Pressing the panels in the...1 replies | 140 view(s)
-
1 Day AgoI’ll try this tomorrow and will let you know. Thanks John!11 replies | 458 view(s)
-
1 Day Agohi max. there is your problem with your base work offset. x and y should be zero. if you look at your video that you took, your g54 offset that you...11 replies | 458 view(s)
-
1 Day AgoYou can’t beat a Thor hammer for getting things square.6 replies | 258 view(s)
-
1 Day AgoHi John. For some reason I can’t upload pictures at the moment. There is error message when trying to upload. Anyway, I have check many stuff on this...11 replies | 458 view(s)
-
1 Day AgoLloyd Barnes started a thread Help with Mach 3 - Cant get the motors to respond in General ElectronicsHi, I think I'm going mad! Can you help?! I converted a manual mill a couple of years with some help from this forum, and its been working...2 replies | 131 view(s)
-
1 Day Agocropwell replied to a thread NEJE laser engraver question vector instead of raster in Laser Machines & BuildingWow! I didn't realise this forum was so popular. Without a major firmware change, your laser engraver is destined to remain as is. You might want...2 replies | 1211 view(s)
-
1 Day AgoRichard replied to a thread NEJE laser engraver question vector instead of raster in Laser Machines & BuildingCan't believe a 1000 people read this, but no replies! :neglected: Oh well. I'll get my coat...2 replies | 1211 view(s)
-
2 Days AgoHey,this is the first wooden toys i made.0 replies | 96 view(s)
-
2 Days AgoHows things going with these screws? Had any luck? If you're still looking for oil/grease recommendations, Lee gave me a great reply recently -...10 replies | 1039 view(s)
-
2 Days AgoAfter some lurking, quite a few questions, a lot of sums and some FEA I've just started building my first machine. It's not as big as I really need...0 replies | 141 view(s)
-
2 Days AgoThanks John. I’ll post some pictures tomorrow. I’ve changed the base offset a while ago and now I'm not sure how to reset it to the system default....11 replies | 458 view(s)
-
2 Days Agoso I've had a look at your video and I am sure that the work offset is correct as the two figures where the machine moves to are the same distance...11 replies | 458 view(s)
-
2 Days AgoI've started making architectural models and learnt the basics of 3D printing. Quite happy with the results and investigating if I can model...0 replies | 162 view(s)
-
2 Days AgoHi. Here is a Youtube link with the short video showing how I can't save the G54 position. Sorry for the annoying music on the background :) I've...11 replies | 458 view(s)
-
2 Days AgoYou could also try the wonderfully named http://www.thehairyworm.co.uk/ :rolleyes:12 replies | 14639 view(s)
-
2 Days Agojamesgates1000 replied to a thread FOR SALE: Denford Triac - Fanuc OM with BT30 8 Position ATC in Items For SaleStarting at £5000 +VAT.2 replies | 190 view(s)
-
2 Days Agoroutercnc replied to a thread Looking for advice on converting driver on Boxford CNC Router to Mach3/4 in Boxford RoutersJazzcnc has not posted on here for a while and regulars who do post on here and know him personally say he is fine but busy. He has probably not...8 replies | 1446 view(s)
-
2 Days AgoChaz replied to a thread FOR SALE: Denford Triac - Fanuc OM with BT30 8 Position ATC in Items For SaleEveryone will ask for a price ..... so might as well do it on their behalf.2 replies | 190 view(s)
-
2 Days AgoYep, share the code. It sounds like a mixup of settings (G91.1 sets Incremental mode). G90 & G91 Distance Mode Interpretation of Mac code can be...5 replies | 292 view(s)
FOR SALE ShaperOrigin Handheld CNC...
4 Hours Ago in Items For Sale