Activity Stream
-
Older Activity
-
7 Hours Agoroutercnc replied to a thread Please help identify these CNC machines found at my school. (should make PCBs) in General DiscussionOK flipped them around for you. Could be well off track here but a small enclosed machine for education makes me think Denford / Denford...1 replies | 79 view(s)
-
18 Hours Agochazzy2501 started a thread Please help identify these CNC machines found at my school. (should make PCBs) in General Discussion2 of these have been found in a cupboard here at the school, with a new belt I think they can work again. (I've been here since 2005 and never seen...1 replies | 79 view(s)
-
1 Day AgoHi Neale, I will try what you have suggested, seems to be the right way to go. Ooznest has been good but I think there is a communication breakdown....5 replies | 255 view(s)
-
1 Day AgoAs a quick sanity check, have you tried comparing cable colours between each of the axes? There is always the possibility that a cable connector is...5 replies | 255 view(s)
-
2 Days AgoLooked at that link, and will try that as a last resort but ty for it, really appreciate it5 replies | 255 view(s)
-
2 Days AgoJust done a little bit of research. Looks like the Ooznest relies on prewired harnesses and a bunch of configuration files to set machine parameters....5 replies | 255 view(s)
-
2 Days AgoTwo points to note before I suggest something: - I don't know the Ooznest hardware kit at all, so not sure how the stepper motor to driver...5 replies | 255 view(s)
-
2 Days AgoHi all, I am completely new to everything related to the CNC world, having said that I have had a machine sitting in their boxes for some time now...5 replies | 255 view(s)
-
2 Days AgoWelcome to MYCNCUK.1 replies | 277 view(s)
-
2 Days AgoHi all, Thank you for allowing me to join this forum, My name is Mark and I live in a small village called Alfriston in East Sussex. I retired from...1 replies | 277 view(s)
-
3 Days AgoStarting the enclosure for the knee lift electronics. I seem to like making it complicated!100 replies | 159162 view(s)
-
5 Days AgoWhat are you struggling with?4 replies | 726 view(s)
-
5 Days AgoJohnHaine replied to a thread NEW MEMBER: Denford Triac converted to UCCNC in New Member Introductions...or there!4 replies | 726 view(s)
-
6 Days AgoJohnHaine replied to a thread NEW MEMBER: Denford Triac converted to UCCNC in New Member Introductionshttps://www.forum.cncdrive.com/ Maybe more likely to find help here.4 replies | 726 view(s)
-
6 Days AgoBeen using my home built cnc mill router for years now for personal use. Its getting a bit worn and after being shipped with our belongings from...0 replies | 435 view(s)
-
6 Days AgoI am looking for a little guidance on how to test my 3 phase spindle with a multimeter to see if there is an issue ,,, as it won't run ,just a slight...0 replies | 513 view(s)
-
1 Week AgoAhmad T replied to a thread NEW MEMBER: Denford Triac converted to UCCNC in New Member IntroductionsWelcome to the forum.4 replies | 726 view(s)
-
1 Week AgoHi All, Looking for some assistance to set up my Triac that I have had retro-fitted with UCCNC software. Any assistance would be much appreciated...4 replies | 726 view(s)
-
1 Week AgoPhil Mayor replied to a thread Testing The VFD, Break Resistor and Wiring to AXBBE in Spindles & Drive MotorsI think I'm going to try to return this VFD, I do think it's quite a good bit of kit, it's just the Chinglish that makes this a much harder job, I've...30 replies | 4886 view(s)
-
1 Week AgoI am running a fuling vfd which until today was fine , the spindle would not operate , trying to start but won't, i then noticed the spindle hz...0 replies | 483 view(s)
-
1 Week AgoPJMCAmbs started a thread FOR SALE: JET 22-44 Plus Drum Sander 240 Volt Axminster with Auto Feed in/Feed out Table. in Items For SaleIntroducing the JET 22-44 Plus Drum Sander, the perfect solution for all your woodworking needs. This high-quality sander boasts a powerful 240 Volt...0 replies | 615 view(s)
-
1 Week Agovoyager1972 replied to a thread touch probe connectivity with ceramic bearings in Machine DiscussionThanks for the reply , that makes things a lot clearer to me now , they operate different from a touch plate.12 replies | 1469 view(s)
-
1 Week AgoThe product description says: "Normally closed specification technical parameters Output mode: BNC (normally closed)" Which implies that it...12 replies | 1469 view(s)
-
1 Week Agomekanik replied to a thread TOSHIBA VF-NC3S VFD for sale (unused) in Classified Ads, Buy, Sell & SwapHi Hank I have very little electrical knowledge so perhaps other members of the forum may be able to help, But i believe that after standing for...1 replies | 505 view(s)
-
1 Week Agovoyager1972 replied to a thread touch probe connectivity with ceramic bearings in Machine Discussionhttps://www.ebay.co.uk/itm/144148210623?chn=ps&_ul=GB&_trkparms=ispr%3D1&amdata=enc%3A1oNeoRdFAREmXcc5QMHyPXg41&norover=1&mkrid=710-134428-41853-0&mks...12 replies | 1469 view(s)
-
1 Week AgoHankMcSpank started a thread TOSHIBA VF-NC3S VFD for sale (unused) in Classified Ads, Buy, Sell & SwapSo, in 2013, I sought advice about a VFD from this venerable forum. (here's the thread -...1 replies | 505 view(s)
-
1 Week AgoBeen having problems with my router. Random limit switch triggering, which seems to be down to either poor connections in a terminal box, or possibly...0 replies | 563 view(s)
-
1 Week AgoCould you post a link please?12 replies | 1469 view(s)
-
1 Week AgoPJMCAmbs started a thread FOR SALE: KEW 1325 8 x 4 CNC Router Machine. 2500 x 1300 x 200 Vacuum Bed + T Slots + PC in Items For SaleNOW SOLD KEW-1325 8' x 4' Vacuum Bed CNC Router Machine . Fully working and complete with computer to run the cnc loads of cutters and bits...0 replies | 532 view(s)
-
1 Week Agovoyager1972 replied to a thread BUILD LOG: My first 3D printer - Bambu Lab P1S in 3D Printing Machinespurchased one for my son at christmas , worked flawlessly out of the box ,he is using it for a school project and it is getting plenty of use. great...4 replies | 1649 view(s)
Please help identify these CNC...