Activity Stream
-
Older Activity
-
9 Hours AgoJust use the widest cutter you have and write a bit of code to make test cuts for both directions on a piece of scrap then adjust as required,...1 replies | 104 view(s) -
15 Hours AgoIs there any easy cheap way to tram the nod on a workbee other than paying over £100 for a gauge1 replies | 104 view(s) -
1 Day AgoNice work. The rigidity of the machine is really showing on the surface finish.19 replies | 18905 view(s) -
1 Day AgoHi, I have found that the DOS software runs very well in the latest version of DosBox X which is free online. My conect cadet plus runs from an...50 replies | 67245 view(s) -
1 Day AgoHi Andrew, I've been using this: Sign Mask Signmask Spandex Avery Dennison Light Blue 380mm EU 54876 A Print Sign Works well, cant use solvent...1 replies | 266 view(s) -
1 Day AgoTo me it looks like you are going to slow with the feed rate1 replies | 129 view(s)
-
1 Day AgoHelp I am surfacing some Ash across grain and its burning, bit is 28.5 Amana 16000rpm stepover 40% speed rate 35 inch per min. Only used the amana...1 replies | 129 view(s)
-
1 Day Agojust bought 1 today hopefuly il get this software up and running thanks guys for your sw and info its greatly appreciated50 replies | 67245 view(s)
-
2 Days AgoJAZZCNC replied to a thread How to setup Chinese AASD Servo electronic gearing in Machine DiscussionDazp suggests a good board because the UB1 is an excellent choice if you are using servos due to the fact its differential line drivers are nice and...11 replies | 9243 view(s)
-
2 Days AgoOK, but how do you expect us to give you meaningful help if you are showing pics that don't match how you have it set up.? My suggestion is that...5 replies | 272 view(s)
-
2 Days AgoI have a cut off saw, but the rotary switch broke whilst in transit. Here is the plate from the motor. There are 6 connections on it U1/V1/W1...0 replies | 106 view(s)
-
2 Days AgoAre you sure the drives are enabled?. Are you sure about the pin numbers?.5 replies | 272 view(s)
-
2 Days AgoHere are some test cuts and accuracy. I am quite happy with the outcome. https://www.youtube.com/watch?v=1ZTpCh8eap4&t=3s19 replies | 18905 view(s)
-
2 Days Agodazp1976 replied to a thread How to setup Chinese AASD Servo electronic gearing in Machine DiscussionYep. You want your step/dir signals wired differential. Using the open collector way like you would with steppers is no use. I was told OC is...11 replies | 9243 view(s)
-
2 Days AgoHi CNCConnect sorry i should have been a bit clearer in my last post, to calculate motor loading the weight of the gantry needs to be known, also...4 replies | 639 view(s)
-
2 Days AgoThe pic is older, I changed it to port #3 and I have read and done what I understand from the manual.5 replies | 272 view(s)
-
2 Days AgoThat was an old pic I put it on port #3.Have read the manual and done everything I understand from it.5 replies | 272 view(s)
-
3 Days AgoJazz answered your question perfectly. But I'll answer with another question. How are you going to interface the UC300eth with the servo? The thought...11 replies | 9243 view(s)
-
3 Days AgoJAZZCNC replied to a thread How to setup Chinese AASD Servo electronic gearing in Machine DiscussionThe 400Khz is per axis output.11 replies | 9243 view(s)
-
3 Days AgoProbably because you are using the wrong Port.? Port #1 which you are using is mostly Inputs, Port #2 and #3 are the ones with all the outputs on...5 replies | 272 view(s)
-
3 Days AgoYour welcome, This offer also goes to anyone else who is lurking in the background and thinking about getting into CNC but is unsure of what's...3 replies | 379 view(s)
-
3 Days AgoGreetings. I hope his is the right place to ask. I recently got another router and the software that came with it for control does not help me at all...5 replies | 272 view(s)
-
3 Days AgoI was thinking about: a worktable size 1000mm x 500mm worktable size mdf 1kW electrospindle vacuub blocking system4 replies | 639 view(s)
workbee tramming