Activity Stream
-
Older Activity
-
2 Hours AgoOk, That's a shame and it will most likely perform ok, but that doesn't mean it's a good choice.! Also, let me just point out that it's a common...18 replies | 1291 view(s) -
6 Hours AgoThe UC100 is a respected device. Be aware there's a grey market out there with fake UC100s - obviously the horse has bolted here, but just go into...18 replies | 1291 view(s) -
7 Hours AgoHi, Thanks for the advice. Alas I placed an order for the UC100 last night, so I'll see how it performs and if I encounter any problems I'll...18 replies | 1291 view(s)
-
9 Hours AgoWhat paint do you guys use for the letters on an external wooden v carved sign which is then oiled0 replies | 56 view(s)
-
17 Hours AgoThanks for the help doody, ordered the parts. I'll give it a try once the isolation board comes.21 replies | 4616 view(s)
-
1 Day AgoThis has just reminded me that I never replied to your email. Ultimately because of memory limitations. When you only had 128k of memory...17 replies | 1655 view(s)
-
1 Day AgoThis is already sold. I thought I had marked it as sold but obviously not :/5 replies | 3338 view(s)
-
1 Day AgoHi JAZZCNC, that really is an incredibly kind offer. I would love to take you up on it, I will drop you an email.2 replies | 181 view(s)
-
1 Day AgoThe copy of the manual I found online suggest pin 61 is a +12V (10mA max) regulated supply. Check that is +12V wrt the common rail (99.9% convinced...21 replies | 4616 view(s)
-
1 Day AgoMach3 is a bad choice, it's unsupported and does have some bugs which won't ever get fixed. UCCNC is far better software that is supported and made...18 replies | 1291 view(s)
-
1 Day AgoHello, iestyn, If you want to take a trip across to Goole you are very welcome to come to visit our Workshop and I will give you a crash course...2 replies | 181 view(s)
-
1 Day AgoHello everyone I have a 1995 Hyundai HIT-15S Lathe and the hydruicla pump has died. I was wondering if anybody could point me in the right...0 replies | 82 view(s)
-
1 Day AgoWhat is the UK equivalent of the stencil film Oramask, seen people using this for v carve painting.0 replies | 97 view(s)
-
1 Day AgoI'm suppose to be working aswell lol. It's a sprint 1200 v1.2. there are two terminals for the 0-10v signal. One been the signal and the other...21 replies | 4616 view(s)
-
1 Day AgoIf you was to write a pot on the spindle controller, you should have 3 pins on the spindle controller to attach to, what are those? Likely a good...21 replies | 4616 view(s)
-
1 Day AgoI have v carved some signs, used sanding sealer then painted with painters touch acrylic paint and i`m getting small paint chips that means I have to...0 replies | 109 view(s)
-
1 Day AgoI'll order one and give it a try. I'll hook up 24v from the machine cabinets PSU. And the 0-10v from the Bob to input 1.(LV side). For the HV side, ...21 replies | 4616 view(s)
-
1 Day AgoFrom what I squinted at with that particular board the circuitry was visible separate from the LV and HV sides. You’d supply the LV from the general...21 replies | 4616 view(s)
-
1 Day AgoThanks Doody. Yes I checked with a multimeter and the Bob shares it's grounds. I was looking at those isolation boards. I checked the motor...21 replies | 4616 view(s)
-
1 Day AgoJohn, I've looked at the link to that board and I can't work it out - but it looks probable (PCB underside image) that the 0V reference for the 0-10V...21 replies | 4616 view(s)
-
1 Day AgoHi, Here's the finished case. I print in a light brown ABS and the patterns are only on the face which is on the plate, so it picks it up into the...2 replies | 197 view(s) -
1 Day AgoVery cool! Thanks for the tip. What type of material are you using on top of the ABS? Sent from my SM-S908U1 using Tapatalk2 replies | 197 view(s)
-
2 Days AgoDid this sell?1 replies | 6308 view(s)
-
2 Days AgoHi Jason OK pm it over and I’ll have a look.17 replies | 1655 view(s) -
2 Days AgoI never found the original manuals but I did manage to convert the machine to use the XC906t/CW20 controller. Overall I am impressed with the little...1 replies | 543 view(s)
-
2 Days AgoThanks for ALL your advice and input, its been a big help. After reading and viewing videos on your recommended UC products, I'm thinking of...18 replies | 1291 view(s)
-
2 Days AgoSold1 replies | 1627 view(s)
-
2 Days AgoI will have to look out my dreadful attempt and share it with you, I covered PCD and peck drilling. I started out using GRBL but due to its limited...17 replies | 1655 view(s)
-
3 Days AgoHere is the followup video showing the updates to the Mini Gcode creator, and how you can download the BETA version of the modules to import into...17 replies | 1655 view(s)
-
3 Days AgoWaiting on some parts to come to tackle the homing sensors. I need a bit of help with the Spindle. I have the spindle working by grounding the SGR...21 replies | 4616 view(s)
Connecting my High-Z-S 720