Activity Stream
-
Older Activity
-
6 Minutes AgoJohnHaine replied to a thread Please help identify these CNC machines found at my school. (should make PCBs) in General DiscussionThat could equally be an asset number, for example. If nearly 4000 units were made they would be better known. Can you take photo 1 again with...4 replies | 117 view(s)
-
19 Minutes Agochazzy2501 replied to a thread Please help identify these CNC machines found at my school. (should make PCBs) in General Discussionit does have a serial number in the thousands 00003882 or something. (hand written)4 replies | 117 view(s)
-
41 Minutes AgoJohnHaine replied to a thread Please help identify these CNC machines found at my school. (should make PCBs) in General DiscussionThat does not look like a commercial product but something made as a prototype in a lab.4 replies | 117 view(s)
-
13 Hours Agoroutercnc replied to a thread Please help identify these CNC machines found at my school. (should make PCBs) in General DiscussionOK flipped them around for you. Could be well off track here but a small enclosed machine for education makes me think Denford / Denford...4 replies | 117 view(s)
-
1 Day Agochazzy2501 started a thread Please help identify these CNC machines found at my school. (should make PCBs) in General Discussion2 of these have been found in a cupboard here at the school, with a new belt I think they can work again. (I've been here since 2005 and never seen...4 replies | 117 view(s)
-
1 Day AgoHi Neale, I will try what you have suggested, seems to be the right way to go. Ooznest has been good but I think there is a communication breakdown....5 replies | 264 view(s)
-
2 Days AgoAs a quick sanity check, have you tried comparing cable colours between each of the axes? There is always the possibility that a cable connector is...5 replies | 264 view(s)
-
2 Days AgoLooked at that link, and will try that as a last resort but ty for it, really appreciate it5 replies | 264 view(s)
-
2 Days AgoJust done a little bit of research. Looks like the Ooznest relies on prewired harnesses and a bunch of configuration files to set machine parameters....5 replies | 264 view(s)
-
2 Days AgoTwo points to note before I suggest something: - I don't know the Ooznest hardware kit at all, so not sure how the stepper motor to driver...5 replies | 264 view(s)
-
2 Days AgoHi all, I am completely new to everything related to the CNC world, having said that I have had a machine sitting in their boxes for some time now...5 replies | 264 view(s)
-
2 Days AgoWelcome to MYCNCUK.1 replies | 289 view(s)
-
2 Days AgoHi all, Thank you for allowing me to join this forum, My name is Mark and I live in a small village called Alfriston in East Sussex. I retired from...1 replies | 289 view(s)
-
3 Days AgoStarting the enclosure for the knee lift electronics. I seem to like making it complicated!100 replies | 159194 view(s)
-
6 Days AgoWhat are you struggling with?4 replies | 732 view(s)
-
6 Days AgoJohnHaine replied to a thread NEW MEMBER: Denford Triac converted to UCCNC in New Member Introductions...or there!4 replies | 732 view(s)
-
6 Days AgoJohnHaine replied to a thread NEW MEMBER: Denford Triac converted to UCCNC in New Member Introductionshttps://www.forum.cncdrive.com/ Maybe more likely to find help here.4 replies | 732 view(s)
-
6 Days AgoBeen using my home built cnc mill router for years now for personal use. Its getting a bit worn and after being shipped with our belongings from...0 replies | 439 view(s)
-
6 Days AgoI am looking for a little guidance on how to test my 3 phase spindle with a multimeter to see if there is an issue ,,, as it won't run ,just a slight...0 replies | 529 view(s)
-
1 Week AgoAhmad T replied to a thread NEW MEMBER: Denford Triac converted to UCCNC in New Member IntroductionsWelcome to the forum.4 replies | 732 view(s)
-
1 Week AgoHi All, Looking for some assistance to set up my Triac that I have had retro-fitted with UCCNC software. Any assistance would be much appreciated...4 replies | 732 view(s)
-
1 Week AgoPhil Mayor replied to a thread Testing The VFD, Break Resistor and Wiring to AXBBE in Spindles & Drive MotorsI think I'm going to try to return this VFD, I do think it's quite a good bit of kit, it's just the Chinglish that makes this a much harder job, I've...30 replies | 4892 view(s)
-
1 Week AgoI am running a fuling vfd which until today was fine , the spindle would not operate , trying to start but won't, i then noticed the spindle hz...0 replies | 488 view(s)
-
1 Week AgoPJMCAmbs started a thread FOR SALE: JET 22-44 Plus Drum Sander 240 Volt Axminster with Auto Feed in/Feed out Table. in Items For SaleIntroducing the JET 22-44 Plus Drum Sander, the perfect solution for all your woodworking needs. This high-quality sander boasts a powerful 240 Volt...0 replies | 619 view(s)
-
1 Week Agovoyager1972 replied to a thread touch probe connectivity with ceramic bearings in Machine DiscussionThanks for the reply , that makes things a lot clearer to me now , they operate different from a touch plate.12 replies | 1478 view(s)
-
1 Week AgoThe product description says: "Normally closed specification technical parameters Output mode: BNC (normally closed)" Which implies that it...12 replies | 1478 view(s)
-
1 Week Agomekanik replied to a thread TOSHIBA VF-NC3S VFD for sale (unused) in Classified Ads, Buy, Sell & SwapHi Hank I have very little electrical knowledge so perhaps other members of the forum may be able to help, But i believe that after standing for...1 replies | 510 view(s)
-
1 Week Agovoyager1972 replied to a thread touch probe connectivity with ceramic bearings in Machine Discussionhttps://www.ebay.co.uk/itm/144148210623?chn=ps&_ul=GB&_trkparms=ispr%3D1&amdata=enc%3A1oNeoRdFAREmXcc5QMHyPXg41&norover=1&mkrid=710-134428-41853-0&mks...12 replies | 1478 view(s)
-
1 Week AgoHankMcSpank started a thread TOSHIBA VF-NC3S VFD for sale (unused) in Classified Ads, Buy, Sell & SwapSo, in 2013, I sought advice about a VFD from this venerable forum. (here's the thread -...1 replies | 510 view(s)
Please help identify these CNC...