Activity Stream
-
Older Activity
-
3 Days AgoAll sorted. Let me know if you need more. Regards.178 replies | 233272 view(s)
-
3 Days AgoHi Bladevane! Would you be able to add me to the drop box as well? Larsson365 AT live.se Best regards178 replies | 233272 view(s)
-
5 Days AgoAdded DRO to the XYZ axis. Here is a video about my solution. If anyone is interested I can share the Arduino file.2 replies | 5912 view(s)
-
5 Days Agoit sure is possible in fact if you check amazon you can find a couple different lasers and also a 3018 kit that comes with both a wanna b spindle and...3 replies | 9499 view(s)
-
5 Days Agospinnert replied to a thread [Help please] 3040 GRBL converted stepper driver issues in Chinese MachinesHi have you set your vref properly? (the tiny potentiometer on the back of stepper driver) is the stepper motor getting hot before blowing? check...1 replies | 3877 view(s)
-
1 Week AgoI agree. It has quickly become my most used saw. I use it for everything, both metal and wood. It is very versatile, simple to set it up and quickly...4 replies | 2821 view(s)
-
1 Week AgoHi Nicolas welcome to the community!4 replies | 1760 view(s)
-
1 Week AgoWelcome to the Forum4 replies | 1760 view(s)
-
1 Week AgoI have one too and for the money it's a game changer.4 replies | 2821 view(s)
-
1 Week AgoNice! Enjoy with your tools/machines.4 replies | 2821 view(s)
-
1 Week AgoWelcome to the forum.4 replies | 1760 view(s)
-
1 Week AgoWelcome.4 replies | 1760 view(s)
-
1 Week AgoThat's a bit awkward, Could be done in two pieces and then welded into the assembly, best option would be wire EDM. Have a look on you tube,...2 replies | 1260 view(s)
-
1 Week AgoHello My name is Nicolas Tyler, and I am located in Los Angeles,CA I work with a CNC router, 3d printing, adn plasma4 replies | 1760 view(s)
-
1 Week AgoThat's interesting as most of the teardown videos I have watched on Chinese spindles of machines like the Precision Mathews PM30 etc all have had...2 replies | 1137 view(s)
-
1 Week AgoAngular contact bearings are the most common bearings in spindles. You might get away with repacking the bearings, however if they've been heated...2 replies | 1137 view(s)
-
1 Week AgoIf the slots need square corners, then they'll need some form of slotting or broaching. That could be achieved in a mill or a lathe with a...2 replies | 1260 view(s)
-
1 Week AgoHi I have a problem in trying to work out how to machine slots on the inside of a cylinder?? I'm trying to make a billet clutch basket I have a mill...2 replies | 1260 view(s)
-
1 Week AgoHi All First post so be gentle :-) I have a MM32L that I have just done a spindle motor conversion on using a 3.6KW servo. I have upped the...2 replies | 1137 view(s)
-
1 Week AgoOk that's great, thanks again. I don't think I will use any DI's or DO's at the moment, just to keep it simple. after I've wired the Limits,...4 replies | 1679 view(s)
-
1 Week AgoI've only ever used the Servo Ready, and Fault DOs, however the only one you probably really need is the Fault output (or possibly just the Ready...4 replies | 1679 view(s)
-
1 Week AgoThanks, m_c. That helps a lot, so I guess I was overthinking this. I'll wire the Limits/ E-Stop as I did before through the AXBB-E Controller. Would...4 replies | 1679 view(s)
-
1 Week AgoThe servo drive limit input is for if you need the limit switch connected to the servo, which for CNC applications I can't think of any reason that...4 replies | 1679 view(s)
-
1 Week AgoIf it's just to make uploading easier, a USB floppy disk emulator might be an option, such as -...4 replies | 1957 view(s)
-
1 Week AgoWell, there appears to be little information online as to what the control software is or what computer it runs on so it will be very hard to advise...4 replies | 1957 view(s)
-
1 Week AgoI need to install USB port for upload program. At the moment I'm using Floppy disk for upload program.4 replies | 1957 view(s)
-
1 Week AgoXYZ axis complete!10 replies | 14881 view(s)
-
1 Week AgoHello again, I’ve managed to get the Servo’s to turn the Motors through my AXBB-E Controller just in bench tests at the moment and at a slow speed, I...4 replies | 1679 view(s)
-
2 Weeks AgoWhat are you hoping for?4 replies | 1957 view(s)
-
2 Weeks AgoHi Chaz, I can do that - once I have recovered from a sudden bout of food poisoning! Basically everything is there with the exception of the power...2 replies | 1778 view(s)
eMachineShop Upgrade