Activity Stream
-
Older Activity
-
1 Hour AgoHiltonSteve replied to a thread BUILD LOG: My Build - I blame you lot for this....! in DIY Router Build LogsOh, the reason I've not been on here much is because I've been busy in my new playground for the last few years... Don't all shout at once but...154 replies | 150151 view(s)
-
1 Hour AgoGot a few bits of aluminium extrusion that I don't need... If anyone is interested let me know and I will see what i can do. Various sizes -...0 replies | 10 view(s)
-
2 Hours AgoHiltonSteve replied to a thread BUILD LOG: My Build - I blame you lot for this....! in DIY Router Build LogsMorning all.... Its been a while but I'm back again, and another divorce just sorted out..! Don't take the piss too much...! How is everyone??154 replies | 150151 view(s)
-
2 Hours AgoJohnHaine replied to a thread Please help identify these CNC machines found at my school. (should make PCBs) in General DiscussionThat could equally be an asset number, for example. If nearly 4000 units were made they would be better known. Can you take photo 1 again with...4 replies | 131 view(s)
-
2 Hours Agochazzy2501 replied to a thread Please help identify these CNC machines found at my school. (should make PCBs) in General Discussionit does have a serial number in the thousands 00003882 or something. (hand written)4 replies | 131 view(s)
-
3 Hours AgoJohnHaine replied to a thread Please help identify these CNC machines found at my school. (should make PCBs) in General DiscussionThat does not look like a commercial product but something made as a prototype in a lab.4 replies | 131 view(s)
-
15 Hours Agoroutercnc replied to a thread Please help identify these CNC machines found at my school. (should make PCBs) in General DiscussionOK flipped them around for you. Could be well off track here but a small enclosed machine for education makes me think Denford / Denford...4 replies | 131 view(s)
-
1 Day Agochazzy2501 started a thread Please help identify these CNC machines found at my school. (should make PCBs) in General Discussion2 of these have been found in a cupboard here at the school, with a new belt I think they can work again. (I've been here since 2005 and never seen...4 replies | 131 view(s)
-
1 Day AgoHi Neale, I will try what you have suggested, seems to be the right way to go. Ooznest has been good but I think there is a communication breakdown....5 replies | 269 view(s)
-
2 Days AgoAs a quick sanity check, have you tried comparing cable colours between each of the axes? There is always the possibility that a cable connector is...5 replies | 269 view(s)
-
2 Days AgoLooked at that link, and will try that as a last resort but ty for it, really appreciate it5 replies | 269 view(s)
-
2 Days AgoJust done a little bit of research. Looks like the Ooznest relies on prewired harnesses and a bunch of configuration files to set machine parameters....5 replies | 269 view(s)
-
2 Days AgoTwo points to note before I suggest something: - I don't know the Ooznest hardware kit at all, so not sure how the stepper motor to driver...5 replies | 269 view(s)
-
2 Days AgoHi all, I am completely new to everything related to the CNC world, having said that I have had a machine sitting in their boxes for some time now...5 replies | 269 view(s)
-
2 Days AgoWelcome to MYCNCUK.1 replies | 289 view(s)
-
2 Days AgoHi all, Thank you for allowing me to join this forum, My name is Mark and I live in a small village called Alfriston in East Sussex. I retired from...1 replies | 289 view(s)
-
3 Days AgoStarting the enclosure for the knee lift electronics. I seem to like making it complicated!100 replies | 159200 view(s)
-
6 Days AgoWhat are you struggling with?4 replies | 734 view(s)
-
6 Days AgoJohnHaine replied to a thread NEW MEMBER: Denford Triac converted to UCCNC in New Member Introductions...or there!4 replies | 734 view(s)
-
6 Days AgoJohnHaine replied to a thread NEW MEMBER: Denford Triac converted to UCCNC in New Member Introductionshttps://www.forum.cncdrive.com/ Maybe more likely to find help here.4 replies | 734 view(s)
-
6 Days AgoBeen using my home built cnc mill router for years now for personal use. Its getting a bit worn and after being shipped with our belongings from...0 replies | 444 view(s)
-
6 Days AgoI am looking for a little guidance on how to test my 3 phase spindle with a multimeter to see if there is an issue ,,, as it won't run ,just a slight...0 replies | 534 view(s)
My Build - I blame you lot for...