Activity Stream
-
Older Activity
-
4 Hours AgoHelp me please! I have a CNC laser machine with a 60W tube (bought it in China). In the package with it was a ordinary pump for pumping water. I want...0 replies | 50 view(s)
-
4 Hours AgoThanks a lot! I will try it.2 replies | 404 view(s)
-
5 Hours AgoThis is all really fascinating, thanks for sharing! So I made an 8 x 4 machine frame from I beam profile filled with concrete mix (vid of it being...11 replies | 5073 view(s)
-
6 Hours AgoBongo replied to a thread Adding a Laser to my steel and concrete machine in Gantry/Router Machines & BuildingHey Jazz, Thanks for replying. I have the semi-ridiculous problem of not exactly knowing what I would use it for (though you can bet it will not be...2 replies | 316 view(s)
-
8 Hours AgoOften price depends on your demand. CNC routers can cost anywhere from $350 to $100,000 depending on the size, complexity, speed, and versatility of...18 replies | 13745 view(s)
-
22 Hours AgoGreat thanks for your help6 replies | 186 view(s)
-
22 Hours AgoIf you don't move the material or part then you don't need to reset anything other than the Z height if you changed the tool. If you use the same...6 replies | 186 view(s)
-
22 Hours Agoif I was routering inside and outside the same vector should I rehome and re touch probe inbetween each process.6 replies | 186 view(s)
-
22 Hours AgoHighly likely you moved either x or y zero then.? Other less likely things could be #1 Cam cockup #2 Tool offset applied #3 Material moved #4...6 replies | 186 view(s)
-
23 Hours AgoIt was a 7mm slot with semi circles at both ends, it was the same tools. I set the xyz between runs and the software is v carve pro. The material was...6 replies | 186 view(s)
-
23 Hours AgoGive us a bit more info. #1 What was the vector. Single straight line or a Slot.? #2 Was it the same tool size and number. #3 Did you move...6 replies | 186 view(s)
-
23 Hours AgoOk, I think I can say without anyone objecting that I must be by far the person with the most experience of the "L" shape gantry setup with probably...6 replies | 650 view(s)
-
1 Day AgoI have just cut some slots for some clamps, the through cuts worked fine. I then ran a shallow cut for bolts outside the vector using the same vector...6 replies | 186 view(s)
-
1 Day AgoIt was m_c' s post with a link to his conversion post that helped me & should help others. ...7 replies | 306 view(s)
-
1 Day AgoNow you know, why not add a picture here to help others with the same problem.7 replies | 306 view(s)
-
1 Day AgoAfter an extensive reading of this formidable mine of information, I still have a question as to the choice of the position of the rails on the...6 replies | 650 view(s)
-
2 Days AgoJAZZCNC replied to a thread Panasonic MSD043Axxx Servo Driver pin outs???? in Motor Drivers & ControllersNo problem, Servo manuals are not the clearest of things, and if you are not used to these things it's not always obvious. The good thing is your...22 replies | 837 view(s)
-
2 Days AgoNemo1966 replied to a thread Panasonic MSD043Axxx Servo Driver pin outs???? in Motor Drivers & ControllersAh yes I now see what you are saying, I have a cable already I wanted to know the pin numbering from the FRONT of the cable connector. I didn't...22 replies | 837 view(s)
-
2 Days AgoHi Bill, I have recently been left a workshop of machinery which looks to include a haighton major milling machine. In researching it I came...25 replies | 32802 view(s)
-
2 Days AgoHi all just built my cnc and trying to come to terms with fusion 360 so thought i better sign up and start asking for help haha0 replies | 96 view(s)
-
2 Days Agothe C beam is something else, for cheaper builds, does not accommodate properly square linear rails or ball screw, its more for ultra low cost builds...3 replies | 474 view(s)
-
2 Days AgoJAZZCNC replied to a thread Adding a Laser to my steel and concrete machine in Gantry/Router Machines & BuildingLasers are not my thing but I know that if it's just for laser etching then it's easy enough, but if you are wanting to cut thicker material then...2 replies | 316 view(s)
-
2 Days AgoAlong the same lines as the C Beam profile you can buy from various places, have to have a closer look at that profile when I get time lol3 replies | 474 view(s)
-
2 Days Agodazp1976 replied to a thread Panasonic MSD043Axxx Servo Driver pin outs???? in Motor Drivers & ControllersAs in the 'plug-in to the drive' side is configured as long rows...... The solder tabs on the back 'cable side' are configured as the diagram. ...22 replies | 837 view(s)
-
3 Days AgoJAZZCNC replied to a thread Panasonic MSD043Axxx Servo Driver pin outs???? in Motor Drivers & ControllersOk, now I can see the connector properly I can tell you that it's exactly the same connector as the pics I posted. So in your original post, the...22 replies | 837 view(s)
-
3 Days AgoFound them thanks m_c I just didn't realise they were on the back of that green plate lol7 replies | 306 view(s)
-
3 Days AgoYes I realise that thanks Dean but was just seeing if it would be possible to save some money to start out, looking at the cost to buy the machine &...4 replies | 245 view(s)
-
3 Days AgoJAZZCNC replied to a thread Panasonic MSD043Axxx Servo Driver pin outs???? in Motor Drivers & ControllersYes, they would use a 72pin at the other end if that is what was needed on the board, this is not uncommon. My Yaskawa Spindle servo drive uses a...22 replies | 837 view(s)
chiller