View Full Version : Routers, Spindles & Controllers

  1. Spindle help, please advise
  2. Measuring Spindle Runout
  3. DIY spindle design
  4. correcting mill spindle runout
  5. Router spindle idea
  6. Router/Spindle choice
  7. Trend T4 Router
  8. Spindles for Taig CNC?
  9. DIY Spindle - What type of bearings are best suited for a spindle.
  10. Knackered DeWalt Router
  11. fenner spindle board
  12. setting up Moeller VFD to chinese spindle
  13. Help with spindle control
  14. Spindle Speed Measurement
  15. spindle bearings overheating
  16. Chinese 1.5kw Spindles
  17. VFD + motor
  18. Drawing of water cooled spindle
  19. spindle interferance.
  20. Diy brushless spindle
  21. Mach3 Controlling Huanyang HY02D223B 2.2KW VFD
  22. VFD (?) tripping RCD
  23. Router bit recommendation, spindle speed and feed rate?
  24. High speed spindle for Sieg X1
  25. Water cooled chinese spindle collets, Advice from owners please
  26. Chinese Spindles
  27. ohms in chinese spindle
  28. What size water hose for 2kw spindle?
  29. Spindle lock mechanism for 2.2kW china spindle
  30. VFD Cable and 2.2kw spindle wiring
  31. Spindle torque required
  32. Adjusting speed with vfd
  33. How to connect 2.2KW Inverter VFD?
  34. Photointerruptor circuit for spindle speed
  35. VHD Mounting problem
  36. Poorly siemens inverter, wont switch on.
  37. 50/60 volt spindle inverter.
  38. Speed control
  39. Spindle Stop?
  40. dc motor - spindle / shaft drive
  41. Problems with spindle / motor
  42. Teco inverter
  43. 2.2kw spindle set up
  44. Problems with Kress routers
  45. The 2.2Kw Chinese Spindles - Info, Setup and Advice + More
  46. My spindle has arrived!
  47. Adding earth cable to 2.2Kw Chinese Spindle
  48. Huanyang VFD control plugin for Mach3, USB RS-485
  49. Plugs and sockets
  50. Help needed connecting IMO JAGUAR VFD to Orac
  51. VFD in main electronics cabinet/general layout?
  52. spindle interferes with steppers
  53. Spindle Speed Control
  54. Chinese 300W DC spindle - is the spindle shaft grounded?
  55. ashe fx1500
  56. little Makita RT0700C router trimmer
  57. Porter Cable Router
  58. New Spindle
  59. Spindle Water Pump
  60. DIY Brushless spindle
  61. VFD to USB WIRING ????
  62. Cooling a water cooled spindle, without pipes everywhere & huge water tanks/buckets!
  63. PCPPS B.O.B. - OK for spindle control?
  64. 800w spindle - noise & controlling remotely
  65. Advice on spindle inverter spec
  66. VFD Tripping an RCD
  67. 2.2kw servo motor for spindle
  68. Q: Start Kress 1050 with Gecko540?
  69. hitachi wj200 vfd and modbus
  70. Spindle for sable 2015
  71. Do you need to water cool erhm a water cooled spindle?!!
  72. Anybody used these ? Hertz Brand spindle
  73. Powertran VFD problem
  74. EMCO Spindle Control
  75. Mechatron HFS range of Spindles
  76. 2.2kw spindle Heating Up
  77. Spindle motor rewind
  78. Router has died. Need Advise Please.
  79. Help for MOTOR 2.2 Kw and control board.
  80. Help with 1.5kw Chinese spindle. Wrong plug.
  81. Need repacement controller for CNC 3040
  82. Need help with a sensorless vector VFD and 2.2kw motor.
  83. Need help with a sensorless vector VFD and 2.2kw motor.
  84. High speed router for aluminium tooling 3d profiling.
  85. VFD problems, please help. error code DL
  86. VFD problems, please help. error code "DL"
  87. spindle with compressed air release collet
  88. Spindle Maintainance
  89. machining aluminium with 1.5kW spindle
  90. spindle with compressed air release collet
  91. Improve Kress TIR or get an upgrade?
  92. VFD went pop today
  93. Feed and speed equation
  94. Spindle upgrade
  95. Fitting a pot to a Chinese Spindle VFD
  96. AC servo motor to replace a 3 phase induction motor on a mill spindle.
  97. VFD to motor cable wire size (Gauge)
  98. Anyone familiar with Hitachi X200... a few Q's.....
  99. VFD error
  100. Connecting VFD
  101. magic smoke escaped from my chinese VFD
  102. TB6560 controller Runs spindle on power up When Mach3 plunges spindle stops
  103. VFD upgrade
  104. Never do ebay after a few Jack Daniels!
  105. Porter Cable 75182 Router on 110V site transformer.
  106. Could do with some advice on the two invertors i have aquired
  107. Haunyang VFD input voltage
  108. Eding CPU5A4E controller and Siemens G110 VFD.
  109. Conect 121 DC spindle motor help!
  110. Looking for an CNC xPro controller board
  111. 2.2kw spindle on ebay, worth it?
  112. Wiring limit switches
  113. how to operate chinese spindle from ebay
  114. Toshiba modbus
  115. Water cooled / air cooled 2.2kw spindle
  116. mitsubishi freqrol spindle drive
  117. Arel Spindles
  118. Porter Cable 22-7519-60 Router Motor Issue
  119. 2.2KW 3HP Inverter help
  120. Where are you buying spindles from - new build
  121. MCB reccomendation for router
  122. Torque / Speed curves for different Spindle Types
  123. 1.5Kw Chinese Spindle help
  124. 2.2KW water cooled spindle and Altivar 12 2.2kW 230V 1ph to 3ph
  125. Grounding help, UCCNC, UC300 and connection loss
  126. 1.5 kw Chinese spindle cable
  127. Spindle wiring help
  128. Brushless DC Motor - Mach3 Compatible - Opinions?
  129. Problem with Spindle not spinning
  130. Weird problem - stepped/staged deceleration on Huanyang 2.2kw Spindle
  131. VFD choice
  132. Which thickness CY cable do I need for 1.5kW spindle?
  133. Chinese 2.2kW spindle - wow & flutter
  134. Connecting 2.2kw vfd to Mains supply
  135. Controlling the spindle RPM
  136. VFD ASKPOWER A131 Need Help!
  137. Help needed! Servo, MACH3 or Pokeys57CNC whats going on?
  138. Which circular connector for spindle
  139. Kress 1050 speedcontroll fix / PID controler
  140. Irregular Spindle Speed
  141. Vfd cable
  142. PWM "analogue" spindle speed control and VFDs
  143. ER16 Collet nut problem
  144. Cheap CNC breakout board for controlling spindle speed, will this work?
  145. Again Pokeys57CNC problems, anyone using it?
  146. Hand held CNC router?!
  147. DIY Spindle Drawbar?
  148. Schneider Altivar 320 wiring / setup help needed