PDA

View Full Version : Bridgeport Servo Motors--Mach3 Compatible?



JPB33
02-07-2016, 11:16 AM
My son has a Bridgeport Ez-trak CNC series 1 mill dating from 2002 which is fitted with an Accurite cnc controller and MTS074-44 servo motors. It looks like the servo motors have an encoder fitted, there are also glass scales which feed into each servo assembly.

We would like to use this machine with Mach3 which we also use on a Seig KX3 with great success.


As it looks like the servos are self contained is it possible to use a breakout board or something like that to connect to a pc and Mach?


Or has anyone has some experience of the machine and is able to point us in the right direction or have we got to change the servo motors for steppers?


Thanks

Peter

JAZZCNC
02-07-2016, 07:42 PM
Can you give more info on the servo amps. I think the Motors will be SEM with that code and high possibilty the amps will be either Anilim or Bosch.
If not can you post pictures of the wires and connections going into the amps.

There's high chance they are Analog amps in which case you'll need external controller that outputs +/-10v analog signals.

The fact it has Glass scales suggests what you think are encoders are actually tacho's. The glass scales are providing the position feedback. This also backs up the +/-10v possibilty. Tacho Also suggests they are Brushed DC servos which are often fitted to older machines

JPB33
03-07-2016, 08:23 AM
Thanks for the reply. Yes they are brushed servo motors and made by SEM. Inside the display unit it looks like there is a breakout board and then further boards, seems to spread everywhere!

Since posting I've read more and it seems a better way would be to replace the originals with NM 34 stepper/servo motors asnd use an appropriate breakout board so thats what we're considering doing?

JAZZCNC
03-07-2016, 10:36 AM
Yes there will be board but it's not forced to be Breakout board in the same sense as what your thinking. It will I/O board that's designed to work with the Accurite controller. Similiar to this below. This can't be used as BOB like what your thinking.
18851

Regards Replacement I would think very carefully about what you use and all that goes with each. ie:

Steppers are simple and easy to impliment and can be if required (but wouldn't) run direct from parallel port. However they do not compare to DC Servo's so you'll take a big hit on performance/smoothness/power.

AC Brushless servo's which you'll most likely repace the DC Brushed ones with will be direct replacement and will perform equal or better. However then they cannot be run direct from PP because doesn't provide high enough pulse rate. This then means you need External motion controller to get full performance from servos.
That said even with Steppers you'd be best advised to fit external motion controller to get the best from steppers.

Another option If the drives and motors are working fine is to just replace the controller with Analog external motion controller designed for mach3. Like the excellent Cslabs IP-A which I personaly use or Kflop from Dynomotion.

Third option is to just replace the DC drives with Step/Dir drives and then you can use Standard setup.

The honest truth is that there's no cheap way to do this correctly. Yes you could just replace the motors with steppers and use the PP. But do this correctly still isn't cheap because large steppers are not exactly cheap also require drives that can accept high voltage which are not cheap. Then take into account the massive performance hit you'll take and potential hassle the PP can give. This to me would rule them out.
This approach is the old school way it was done because Servos where stupidly expensive and external motion controllers for mach few and far between. This is no longer the case.
Chinese AC Servos while still not exactly cheap are much lower in price than years ago and within reach of DIY. Put it this way you'll pay as much for large Stepper/Drive setup. You'll still need an external motion controller for mach because of pulse rate required but to be honest you'd need one for steppers to get the best from them.

If it was me and the DC Drives/motors are working fine then I'd just buy the IP-A controller and away you go. There's no Break out board required and it offers loads of I/O along with built in spindle speed control.
If at later date have any issues with drives/motors then replace with Chinese Servo/drives which accept both step/dir and Analog input.

See this Video I made showing the chinese servos/drives. It also shows the Cslabs IP-A and explains couple of things why I used it rather than Step/Dir version. (which I also own)


https://www.youtube.com/watch?v=tW8knRAOr7s

JPB33
04-07-2016, 04:12 PM
Thanks for the comprehensive reply, Lots to consider there! Think the stepper/servo motor route looks most attractive as it would enable a 4th axis to be easily added--but we will see after we have thought about it a bit more.

komatias
04-07-2016, 05:01 PM
Thanks for the comprehensive reply, Lots to consider there! Think the stepper/servo motor route looks most attractive as it would enable a 4th axis to be easily added--but we will see after we have thought about it a bit more.

Have you considered just upgrading the Anilam? It seems a bit of a waste to rip the machine to bits with it only being a 2002. If it is to have easier GCode input, I am sure the new controllers will have better capabilities. Then again I do not know the cost of replacing the Anilam so it may financial sense to do a full conversion.

I have been looking at some controllers recently that are reasonably priced and have up to 5 axis capability with rigid tapping too and they have not been too bad in terms of price. I am still trying to verify if they are legal in the EU though.

JPB33
04-07-2016, 06:45 PM
Thanks for the reply. Yes it does seem a big step to make so many changes to the machine espacially as it works. We looked at an upgrade for the existing controller but it was very expensive and as we also have a Seig KX3 which runs Mach3 we are familiar with it. Havent decided yet but the Mach route was also give us options on adding more axis.

JAZZCNC
04-07-2016, 07:04 PM
I have been looking at some controllers recently that are reasonably priced and have up to 5 axis capability with rigid tapping too and they have not been too bad in terms of price. I am still trying to verify if they are legal in the EU though.

But do these Chinese controllers your looking at output Analog signals or just Step/Dir.? . . . Most I've seen are Step/Dir.

If was me and DC Servos/drives are working fine then I'd just go with the Cslab's IP-A. Doesn't get any easier just little rewiring and away you go and with top notch controller from Top company.

Boyan Silyavski
04-07-2016, 11:52 PM
This type of upgrade is a no brainer, like Dean suggested. Everything could be ripped out and rewired in a day.. ~700 euro but you keep the good motors you have. Final result- a modern machine that will do 3d, 4rth axis and so on. Which otherwise could cost arm and leg. Then you could fit a stepper if you like for the additional axis.

John S
05-07-2016, 12:21 AM
He needs the Cslab's IP-A for those Dc motors but can that do step and direction for the 4th axis ?

JAZZCNC
05-07-2016, 01:24 AM
He needs the Cslab's IP-A for those Dc motors but can that do step and direction for the 4th axis ?

Nope it can't and you bloodly well now it can't you old Git. .:devilish: . . . Anyway 4th axis wasn't mentioned when I suggetsed that route.

To be totally honest (and think John S would agree) if it's working OK I wouldn't touch I'd just sell it and retro fit an Old VMC.!!

John S
05-07-2016, 09:47 AM
Nope, genuine query as I have never used the CS Labs gear and some of the Chinese controllers can do 0 -10v and step and direction.

Personally if it were mine I'd go the IP-A route as I'd not thought of that solution.

Anyway less of the Git .:applause:

komatias
05-07-2016, 10:17 AM
Nope it can't and you bloodly well now it can't you old Git. .:devilish: . . . Anyway 4th axis wasn't mentioned when I suggetsed that route.

To be totally honest (and think John S would agree) if it's working OK I wouldn't touch I'd just sell it and retro fit an Old VMC.!!

Can still rig up a servo on analogue via belt drive to actuate the 4th if going the IP/A route surely?

Gary
05-07-2016, 01:09 PM
Servos are +/-10V not 0-10V.
0-10V are typically for speed control for spindle and these controllers.
I have a few stand alone controllers from China and they are all step and direction.
Not seen one that is fully closed loop with the encoders going back to the controller, so if you know of one, can you link it?

Also there are stepper drivers that will accept +/-10V as well, so if you need another axis on the CSMIO/IP-A you can use a stepper motor, but it needs to be closed loop with an encoder fitted, so will not be much lower price than a servo.


Nope, genuine query as I have never used the CS Labs gear and some of the Chinese controllers can do 0 -10v and step and direction.

Personally if it were mine I'd go the IP-A route as I'd not thought of that solution.

Anyway less of the Git .:applause:

JAZZCNC
05-07-2016, 04:23 PM
Anyway less of the Git .:applause:

Oh ye Sorry forgot your official title is Old B''####d. . Lol


Nope, genuine query as I have never used the CS Labs gear and some of the Chinese controllers can do 0 -10v and step and direction.

Personally if it were mine I'd go the IP-A route as I'd not thought of that solution.

Well I've not seen any, well any that are affordable anyway. Likes of your Siemans etc may well but they are very expensive. Also think you mean +/-10v not 0-10v different animal.


Can still rig up a servo on analogue via belt drive to actuate the 4th if going the IP/A route surely?

Yes course can if got spare axis but John asked if IP-A could output Step/dir as well which it can't.

m_c
05-07-2016, 11:10 PM
With a KFlop & Kanalog it's possible to use both +/-10V and step/dir, however to use the step/dir outputs you have to sacrifice Kanalog encoder inputs.

JAZZCNC
05-07-2016, 11:43 PM
With a KFlop & Kanalog it's possible to use both +/-10V and step/dir, however to use the step/dir outputs you have to sacrifice Kanalog encoder inputs.

Moray can you Mix n match or is it one or tuther..?

m_c
06-07-2016, 12:05 AM
Moray can you Mix n match or is it one or tuther..?
Mix and match.

There are 8 encoder channels (actually 16 differential inputs on the Kanalog - they're not solely for encoder inputs), which at KFlop level means 16 inputs, but those 16 inputs are actually general purpose IOs which also provide the Step/Dir outputs.
4 of the encoder channels go through a separate RJ45 (Ethernet style connector) cable to the Kanalog, with the other 4 being in amongst the main 26pin ribbon cable with all the other signals. If you only need 4 encoders, you can simply make up your own cable to take 4 sets of Step/Dir signals from the RJ45 connector on the KFlop. Otherwise you have to start splitting cables depending on how many encoders and Step/Dir signals you need.

JAZZCNC
06-07-2016, 08:06 AM
Mix and match.

Just looked at the manual because was curious and got to say that's one of the best most comprehensive manuals I've ever seen.