PDA

View Full Version : Play in my mount



CrazeUK
28-02-2017, 07:55 PM
Hi Guys.

So i have a Kress router FME150 mounted onto my CNC.
I finally got the machine cutting yesterday, but noticed it had a little play where the mount is attached to the gantry mount.

How do i tighten it?

I tried to take the Kress out of the mount, but it feels near enough impossible without taking the gantry off.

See the pic.

20922

cropwell
28-02-2017, 11:52 PM
Hi Craze,

My guess is that the plate bolted to the spindle mount is loose. It looks as though you need to take out the Kress and tighten up the backing plates, but there is not enough detail in the photo to be sure.

Alternatively, you could just knock that red wedge in :whistle:

Rob

CrazeUK
01-03-2017, 04:21 AM
Damn. Was really hoping to not have to do that. The kress is a nightmare to remove.

What other pics do you need?

Did try the red wedge but it was too thick lol.

Oh is it worth getting a new mount with a vacuum mount built on, or can you get attachments for the current mount?

Sent from my SM-N930F using Tapatalk

Clive S
01-03-2017, 09:20 AM
Damn. Was really hoping to not have to do that. The kress is a nightmare to remove.

What other pics do you need?

Did try the red wedge but it was too thick lol.

Oh is it worth getting a new mount with a vacuum mount built on, or can you get attachments for the current mount?

Sent from my SM-N930F using Tapatalk

Exactly what is the difficulty of removing the Kress Is it not just held in with cap head bolts

cropwell
01-03-2017, 10:29 AM
My guess is that you have this mount https://damencnc.com/en/tools/kress/kress-milling-motor/147 and there is a plate bolted to the mount, which in turn bolts to the Z axis and it is the plate bolted to the mount which has worked loose.

If that is so you will need to dismantle and reassemble using threadlock. There is also the possibility that the bolts are slightly too long and are bottoming on the thread. Anyway, you will need to get it apart to see what is going on.

Yep, the red wedges are too thick, try a green one :yahoo:

Rob

CrazeUK
01-03-2017, 03:05 PM
Exactly what is the difficulty of removing the Kress Is it not just held in with cap head bolts
When you loosen the nut, the kress is quite firmly stuck.

I will have to probably remove the whole assembly off the gantry.

Sent from my SM-N930F using Tapatalk

CrazeUK
01-03-2017, 03:09 PM
My guess is that you have this mount https://damencnc.com/en/tools/kress/kress-milling-motor/147 and there is a plate bolted to the mount, which in turn bolts to the Z axis and it is the plate bolted to the mount which has worked loose.

If that is so you will need to dismantle and reassemble using threadlock. There is also the possibility that the bolts are slightly too long and are bottoming on the thread. Anyway, you will need to get it apart to see what is going on.

Yep, the red wedges are too thick, try a green one :yahoo:

Rob
I think it looks very similar. I'll take the whole thing off and see if I can get a better pic, or tighten.

The yellow one seems a bit soft for the job. 🤔

Sent from my SM-N930F using Tapatalk

cropwell
01-03-2017, 03:20 PM
When you loosen the nut, the kress is quite firmly stuck.

After loosening the pinch bolt use the red wedge to gently open up the clamp. The Kress is probably stuck in with GES (general engineering shite).

CrazeUK
01-03-2017, 03:22 PM
After loosening the pinch bolt use the red wedge to gently open up the clamp. The Kress is probably stuck in with GES (general engineering shite).
Cool will try. Was just scared the wedge would damage the assembly on the gantry because of the leverage action. Will try again.

Lol GES a technical term. One for me to memorize. Lol

Sent from my SM-N930F using Tapatalk

cropwell
01-03-2017, 03:59 PM
GES is just one of my expressions.

Neale
01-03-2017, 08:12 PM
Posh way is to take out the clamp screw and tap the clearance hole a size larger. You can then use a jack screw down the hole to controllably open the slot. On the other hand, I have a chunky screwdriver that has one of those red arrows painted on the tip; inserted carefully you can open the slot enough without unduly loading the gantry and the marks will be in the slot and won't show...

CrazeUK
03-03-2017, 06:27 PM
So an update. Play in mount issue sorted. I managed to get it out. Un bolt the holder from the assembly, and get to the bolts the other side, one of the 2 was totally loose. Problem solved. 👍👌 - best thing. No wedges 😂😂

Sent from my SM-N930F using Tapatalk