custom guide for 3d printer or router

[alaamomen9]

first i working on design to work as router and 3d printer but i have limit in money
my frame will be alumium 40*80
so i admire this diy
i think on using this instead of supported rail
Is it good !?https://uploads.tapatalk-cdn.com/20170414/d1fbb4c2fa821c6e31ae6c785d9c6bda.jpghttps://uploads.tapatalk-cdn.com/20170414/986b9c73b845b08fec3cc08b3a4b8169.jpg

Sent from my ASUS_Z00A using Tapatalk

[Greeny]

first i working on design to work as router and 3d printer but i have limit in money
my frame will be alumium 40*80
so i admire this diy
i think on using this instead of supported rail
https://uploads.tapatalk-cdn.com/20170414/d1fbb4c2fa821c6e31ae6c785d9c6bda.jpg
Is it good !?



I don't think that's a very good design for many reasons.
If you are going to use it for a router, it's a very bad design as any debris(dust, chips,swarf etc.) would cause big problems.
Also for any use, it will be difficult to make sure your aluminium frame is straight & level.

Have you considered using vee rail?
They can be made from cheap angle iron using a hand held grinder & simple jig.
They are pretty tolerant of debris, and they can be aligned and shimmed relatively easily.
The v-bearings themselves can be hard to find at a reasonable cost though, so look in to that first if you are interested. (try https://www.aliexpress.com/wholesale?catId=0&initiative_id=SB_20170414051833&SearchText=v+groove+bearings )

The mechmate uses v-rails on all axes and there is a TON of information about them on their forum http://www.mechmate.com/forums/index.php

Cheers

21396
21395
21394

[alaamomen9]

I don't think that's a very good design for many reasons.
If you are going to use it for a router, it's a very bad design as any debris(dust, chips,swarf etc.) would cause big problems.
Also for any use, it will be difficult to make sure your aluminium frame is straight & level.

Have you considered using vee rail?
They can be made from cheap angle iron using a hand held grinder & simple jig.
They are pretty tolerant of debris, and they can be aligned and shimmed relatively easily.
The v-bearings themselves can be hard to find at a reasonable cost though, so look in to that first if you are interested. (try https://www.aliexpress.com/wholesale?catId=0&initiative_id=SB_20170414051833&SearchText=v+groove+bearings )

The mechmate uses v-rails on all axes and there is a TON of information about them on their forum http://www.mechmate.com/forums/index.php

Cheers

21396
21395
21394
I think i can't this notch with grinder i will bring angle and put vgroove on it
is it ok!?


Sent from my ASUS_Z00A using Tapatalk

[Greeny]

I think i can't this notch with grinder i will bring angle and put vgroove on it
is it ok!?
Sent from my ASUS_Z00A using Tapatalk

I have never made any v-rail myself, so i can't offer any advice.
I only suggested it as a low cost alternative for you to consider.

Your best place for information and advice would be the mechmate forum i linked to.
There are lots of people there who have experience of making and using v-rails.
There are literally hundreds of posts about making, aligning, and using v-rail.
Prepare for a lot of reading ☺

Cheers

[magicniner]

Also for any use, it will be difficult to make sure your aluminium frame is straight & level.


If you aren't sure and don't have a good means of determining that any rail is straight then you're guessing and are thus stuffed anyway, likewise level and square are a guess unless you measure them.

Bent rails can be straightened if you have means to measure errors in straightness, level and square can also be adjusted if you have the required metrology.

Vulnerability to contamination is to a large extent a design issue.

- Nick

[Greeny]

If you aren't sure and don't have a good means of determining that any rail is straight then you're guessing and are thus stuffed anyway, likewise level and square are a guess unless you measure them.

There is a tried, tested, simple and cheap way of aligning and levelling v-rail using a tensioned wire along the apex of the rail.
Methods for this are given in great detail on the mechmate forum i linked to



Bent rails can be straightened if you have means to measure errors in straightness, level and square can also be adjusted if you have the required metrology.


The op has already stated that the budget is tight, too tight for supported rails, so i was guessing it would also be too tight for the 'required metrology'. Besides, even if the aluminium square tube could be straightened its still a terrible design.



Vulnerability to contamination is to a large extent a design issue.
- Nick
Exactly, which is why i suggested looking at an alternate budget design that is proven to have low vunerability to contamination.