PDA

View Full Version : Anyone have a UK source for open ended 10mm T5 Polyurethane belt



cweeks
27-02-2010, 07:32 PM
Hi,

I have a need for around 7 meters of open ended (i.e. off the roll) 10mm wide T5 Polyurethane belt. I have found a US source at a sensible price, see here http://shop.polybelt.com/10T5-Open-End-Belt-Roll-Polyurethane-with-Steel-Cords-B10T5-MPS.htm but unfortunately no shipping to the UK. Does anyone have a sensibly priced UK source they have used ?

Cheers, Cam.

jonm
27-02-2010, 11:55 PM
hi cam
have looked for open ended timing belt in uk before , and could only find this, its not t5 http://www.motionco.co.uk/timing-belts-open-length-belting-c-25_38_49.html

jonm
28-02-2010, 12:28 AM
cam
another option is here not open ended belt but couldnt you get a long belt and cut it http://www.bearingboys.co.uk/Timing_Belts-1039-c

John S
28-02-2010, 12:39 AM
http://www.roulunds.co.uk/product_list.php?top=Positive%20Drive%20Belts%20-%20PU&category=496&sub=%20%20%20%20%20%20%20%20T5

.

mel_earp
28-02-2010, 10:31 AM
Might be worth being a bit careful. This was on that web site.

Codan Rubber Limited – In Administration
Thursday 18th February 2010
The affairs, business and property of the company are being managed by the Joint Administrators who act as agent for the company without personal liability
G P Bushby and M Wild are licensed to act as insolvency practitioners in the UK by the Institute of Chartered Accountants in England and Wales (IP numbers 8736 and 9300 respectively)

cweeks
28-02-2010, 12:38 PM
Thanks for the links, unfortunately I can't cut a belt because I can't find one long enough. I need an axis travel of 1 meter, therefore I need a belt just over 2 meters. The http://www.roulunds.co.uk/ web site looks the best, but the price is still much higher than the US one. I think I may contact the US guys and see if they are prepared to ship to the UK. I will let you know how it goes.

Cam.

Swarfing
28-02-2010, 07:49 PM
Mel
Just to clarify was it MOTIONCO that is winding up? as there it where i am getting my belt from for my build.

TNX

cweeks
28-02-2010, 09:05 PM
I think it was http://www.roulunds.co.uk/ they have Codan plastered all over their web site.

Swarfing
28-02-2010, 09:11 PM
Thats a relief

mel_earp
28-02-2010, 11:05 PM
Sorry. I should have made it clear. On the Roulunds web site it shows the history and they are Codan one and the same. I cut and pasted direct from http://www.roulunds.co.uk/ (http://www.roulunds.co.uk/) .

cweeks
03-03-2010, 08:57 PM
No reply from the USA but I found a UK source at very similar prices. http://www.transdev.co.uk/

cweeks
03-03-2010, 08:59 PM
No reply from the USA but I found a UK source at very similar prices, http://www.transdev.co.uk/

MickS
18-03-2016, 05:22 PM
Hi,

I have a need for around 7 meters of open ended (i.e. off the roll) 10mm wide T5 Polyurethane belt. I have found a US source at a sensible price, see here http://shop.polybelt.com/10T5-Open-End-Belt-Roll-Polyurethane-with-Steel-Cords-B10T5-MPS.htm but unfortunately no shipping to the UK. Does anyone have a sensibly priced UK source they have used ?

Cheers, Cam.
not sure if I'm doing this correctly as it's my first. I've used http://www.beltingonline.com/ they seem to have a wide range of belts puppies and a calculator to find out how much it will cost
Mick

routercnc
18-03-2016, 06:47 PM
Wow Mick that thread is 6 years old !

I know its a typo but it made me chuckle that they sell puppies

MickS
18-03-2016, 07:55 PM
sorry about the puppies, looks like I have my dyslexic fingers on today.
I'll also look at the date next time. this is my first attempts at joining in a forum. therefore, a few bits to learn. glad to have given some one a chuckle though.
Mick

Clive S
19-03-2016, 12:21 AM
sorry about the puppies, looks like I have my dyslexic fingers on today.
I'll also look at the date next time. this is my first attempts at joining in a forum. therefore, a few bits to learn. glad to have given some one a chuckle though.
MickHi Mick welcome to the forum don't worry I think you will find a friendly bunch of sarcastic experts on here all willing to help in any way they can:friendly_wink:

AndyGuid
19-03-2016, 02:09 AM
Welcome to the forum Mick. In my view it's one of the best forums on the web!
.
Andy

routercnc
19-03-2016, 08:10 AM
Yes Welcome Mick no harm meant

Clive S
19-03-2016, 08:43 AM
Yes Welcome Mick no harm meantThat will teach me to post after a few bevies, sarcastic was not meant in any way personal to anybody:cower: