PDA

View Full Version : help with cnc laser



swinds
10-12-2011, 10:43 PM
hiya

i have got a 120w laser from china - problem is when the manuals are translater its quite funny to read - but not funny when u are struggling to set it.....

my question is can anyone help me set the focus of the laser (i think thats the problem) anyone is welcome to come round to my house on the wirral to have a play and use machine time as they want -

any advice would be greatfully received, dont say ask the guy who made it - its like .......in the wind.....

many thanks

Web Goblin
10-12-2011, 11:06 PM
Swinds,
unfortunately you will need the information from the lens and the cutting head to set the focal length. Normally you would be able to adjust the nozzle depth by screwing it in or out of the nozzle holder so that you can get the focal point beyond the nozzle so the actual focal point is inside the material you are cutting, but to do this you would need the focal length to start with.
Can you post a link to what you bought or the manual?

Ian

swinds
10-12-2011, 11:11 PM
hi thanks for taking the time to reply to me

this is where i got it from www.salescnc.com (http://www.salescnc.com)

these are the manuals i got with it

http://www.salecnc.com/manuals/laser/LaserManualV4.1.pdf

http://www.salecnc.com/manuals/laser/Laser_ControlPannel.pdf

i can get it to scratch the surface of a piece if perspex but thats it - i can up the power and it just burns the plastic, so i am assuming ite the focus

thanks

karl

swinds
11-12-2011, 12:48 AM
http://www.salecnc.com/manuals/laser/LaserManualV4.1.pdf

http://www.salecnc.com/manuals/laser/Laser_ControlPannel.pdf

it just scratches perspex and when i turn up the power it just burns the plastic

Web Goblin
11-12-2011, 02:30 PM
The manual is a classic! I can only think of one good use for it.
What is your distance from nozzle to the work piece? It could be that you need to adjust this cutting height to get the focal point in the correct place. Does the laser require a cutting assist gas?

Ian

swinds
11-12-2011, 03:08 PM
the distance is about 30mm but i have an up and down bed so i can make it more - if needed - but think thats the closest it can get

it has an air supply direct to the head

karl

swinds
11-12-2011, 04:18 PM
now i am slowly losing the will to live .......lol

this bloody laser just dont want to play - ive read the manual many times and it just wont play

i cna get it to score or the techinacl term is "burn" plastic and 3mm mdf but thats just on the surface

any advice or free bacon butties if you live close enough.....lol

many thanks

karl

Web Goblin
11-12-2011, 09:59 PM
Karl,
30mm seems to be too far from the cutting surface. I would try to get this distance down to 1mm and try it again. The focal point shouldnt be that far away from the end of the nozzle. If you cant raise the bed or lower the cutting head try putting something under the material to try it.

Ian

swinds
11-12-2011, 10:23 PM
thanks ian

ill give that another go 2morrow - i did try moving the bed closer and seeing what happens but pretty much the same results

thanks

karl

Web Goblin
11-12-2011, 10:42 PM
I did manage to get the web page you linked to to open after searching for it. The link seemed to go somewhere else.
If you got one of their machines complete and ready to go them you shouldnt need to adjust the cutting head height. It looks to be pre-set.
What power and mode settings are you using?

Ian

swinds
11-12-2011, 10:51 PM
i copied all the settings as one of their set up videos - min power 50% max power 1 65% max power 2 65% and speed as 1.2

at those settings on the video they cut acrylic at about 5mm - it just burns everything when i do it...lol

ill get there im sure

karl

Philly
09-01-2012, 10:15 PM
i copied all the settings as one of their set up videos - min power 50% max power 1 65% max power 2 65% and speed as 1.2

at those settings on the video they cut acrylic at about 5mm - it just burns everything when i do it...lol

ill get there im sure

karl


Hi mate, I've just moved back into B'head, so not far from you. If I can wangle a day off I'll pop down and Im sure we can cobble it together between us ;)