nobby

10-06-2013, 04:18 PM

hello, I do realise it IS a complete liberty having your first post as a for sale but read on please.

I just bought an enclosure, cnc / liquid gasket printer, for the desktop Isel Techno FB2 that was inside.

so I am offering all the bits that I don't require, but I do want new motors and controllers, mach3/4 and that, anyways here goes

here is what I bought, took two goes in my little estate car, Fulham London to Stafford, but at least now it is all in bits

http://img.photobucket.com/albums/v222/pantswagen/KGrHqNrEFEJ19cBolBRd7yw4Jw60_121_zps5cc8da6c.jpg

the long side are 90 by 45 = 1450mm

there are six bits

-----------------------

the short sides are 1080mm

there are 6 bits of this - maybe 8

--------------------------

the legs are 90mm by 90mm and have bolt in feet

------------------------------------

there are 4 complete blue panels, for all 4 sides

the buttons on the front could be for auto stop

-----------------------------------------

http://img.photobucket.com/albums/v222/pantswagen/KGrHqNHJEgFEnPjcTtqBRd7yd6TSw60_121_zpsa7770e3d.jp g

if you left it as it is, max width is 1080 plu 90 plus 90 = 1260mm, 4ftand a smidgers

the long then is 1450 plus 90 - leaving the tall legs = 1540mm, 1525 is 5ft

-------------------------------------------

theer are 2 bits of 90 by 45 to make the y axis with, i think another few lengths to make a shelf on the tall legs, and the z axis

-------------------------------------------

there are 2 3/4'' 19mm solid alloy plates to make the gantry ends, there are another two bits of 15mm or 19mm to make the z axis

-------------------------------------------

there are 4 four foot flat sliders with bosch bearings, enough to then do the y axis and loads to make a very rigid z axis.

these are fitted to 4 bits of 60 by 45mm -

THERE ARE ALSO A PAIR OF IAR RAMS AND 2 PUMPS AND LOTS OF PNEUMATIC CONTROLLING STUFF - I DON'T KNOW WHAT IT DOES THOUGH.

http://img.photobucket.com/albums/v222/pantswagen/IMG00729-20130610-1623_zpsd8e1d08b.jpg

there are two of those alloy thick plates with a nice hole in the centre for you to cut a pair of welly boots from, and have the nice radius

----------------------------------------------

also there is stack and stacks of 45mm box, lots of nuts and bolts

all the wireing is there to the controllers about 1998 from what I can see, I can take a pic.

------------------------------------------------

there are 2 old wee amc 3 axis controllers, , two hand held doofers, all the wireing and connectors

all used

IT IS ALL APART, YOU CAN GET IT IN AN ESTATE CAR

I AM WILLING TO POST EVERYTHING - BAR THE BLUE SIDES AT COST.

NOW THE BEST BIT i NEED

http://www.cnc4you.co.uk/index.php?route=product/product&path=20_26&product_id=217

ALSO NEED A SPINDLE AND MOUNT

AND SOME MACH3 - OR 4

OH AND A USB/lan BOB

SO HAPPY TO HAVE A SWAPSIES.

THANKS

I just bought an enclosure, cnc / liquid gasket printer, for the desktop Isel Techno FB2 that was inside.

so I am offering all the bits that I don't require, but I do want new motors and controllers, mach3/4 and that, anyways here goes

here is what I bought, took two goes in my little estate car, Fulham London to Stafford, but at least now it is all in bits

http://img.photobucket.com/albums/v222/pantswagen/KGrHqNrEFEJ19cBolBRd7yw4Jw60_121_zps5cc8da6c.jpg

the long side are 90 by 45 = 1450mm

there are six bits

-----------------------

the short sides are 1080mm

there are 6 bits of this - maybe 8

--------------------------

the legs are 90mm by 90mm and have bolt in feet

------------------------------------

there are 4 complete blue panels, for all 4 sides

the buttons on the front could be for auto stop

-----------------------------------------

http://img.photobucket.com/albums/v222/pantswagen/KGrHqNHJEgFEnPjcTtqBRd7yd6TSw60_121_zpsa7770e3d.jp g

if you left it as it is, max width is 1080 plu 90 plus 90 = 1260mm, 4ftand a smidgers

the long then is 1450 plus 90 - leaving the tall legs = 1540mm, 1525 is 5ft

-------------------------------------------

theer are 2 bits of 90 by 45 to make the y axis with, i think another few lengths to make a shelf on the tall legs, and the z axis

-------------------------------------------

there are 2 3/4'' 19mm solid alloy plates to make the gantry ends, there are another two bits of 15mm or 19mm to make the z axis

-------------------------------------------

there are 4 four foot flat sliders with bosch bearings, enough to then do the y axis and loads to make a very rigid z axis.

these are fitted to 4 bits of 60 by 45mm -

THERE ARE ALSO A PAIR OF IAR RAMS AND 2 PUMPS AND LOTS OF PNEUMATIC CONTROLLING STUFF - I DON'T KNOW WHAT IT DOES THOUGH.

http://img.photobucket.com/albums/v222/pantswagen/IMG00729-20130610-1623_zpsd8e1d08b.jpg

there are two of those alloy thick plates with a nice hole in the centre for you to cut a pair of welly boots from, and have the nice radius

----------------------------------------------

also there is stack and stacks of 45mm box, lots of nuts and bolts

all the wireing is there to the controllers about 1998 from what I can see, I can take a pic.

------------------------------------------------

there are 2 old wee amc 3 axis controllers, , two hand held doofers, all the wireing and connectors

all used

IT IS ALL APART, YOU CAN GET IT IN AN ESTATE CAR

I AM WILLING TO POST EVERYTHING - BAR THE BLUE SIDES AT COST.

NOW THE BEST BIT i NEED

http://www.cnc4you.co.uk/index.php?route=product/product&path=20_26&product_id=217

ALSO NEED A SPINDLE AND MOUNT

AND SOME MACH3 - OR 4

OH AND A USB/lan BOB

SO HAPPY TO HAVE A SWAPSIES.

THANKS