PDA

View Full Version : FOR SALE: Denford MIRAC CNC Lathe. Single Phase. Absolutely complete and perfect running order.



Nick Butler
14-07-2013, 01:01 PM
Denford MIRAC CNC lathe.
Specification: Swing over Bed: 250mm (10)
Maximum Turning Diameter: 160mm (6.25)
Maximum turned length: 180mm (7)
Spindle Bore: 21mm (0.8125) No. 3 M.T.
Spindle Nose Type: A2 42mm (1.625)
Spindle Speeds: 0 5000 R.P.M.
Feedrates: 0 1200mm/Minute
Spindle Motor: 1 H.P.
X axis travel: 85mm (3.375)
Y axis travel: 200mm (8)
Coolant capacity: 18 Litres
Machine resolution: 0.01mm (0.0004)
Machine Weight: 320 Kg. (705Lbs.)
Electrical requirements: 240 Volt SINGLE PHASE
Machine Length: 1090mm (43)
Machine Depth: 970mm (38.2)
Machine Height: 625mm (24.6)
Machine Features:
RS232 Port. Plug for external keyboard. Auxilliary 7 Pin socket.
(Serial Port, Parallel Port) Coolant pump, sump and drain valve.
Internal lighting above work area. Safety interlocked sliding door with window.
Internal and external jaws for 3 Jaw chuck. Chuck key.
4 brand new and 1 used quick release tool holders. Release key and tool clamp key.
Parting off tool with indexable carbide bit and holder.
Built in enhanced colour graphics display and membrane keyboard.
Floppy Disc Drive.
Emergency stop button.
Control Software has over 40 features to allow complete control and federate over-ride of 0 150% Other features include:
Manual Data Input facility.
Internal and External screw cutting.
Tool nose radius compensation.
Metric or imperial Prgramming.
Circular and Linear Interpolation.
Canned Turning Cycles.Tool Offsets for 16 Tools
Dry Run facility.
Toolpaths Graphics in colour 2D or 3D display.
Program merging facility.
Jog mode with variable feedrates.
LAN communication if required.
Axis over-travel limits.
And many more (Contact me for full list)

Software and Complete Documentation:
MillCam Designer software. Post Processor Libraries
Denford Industrial Text Editor software. Denford Dongle
MIRAC Maintenance manual MIRAC operating software and backup disc.
Denford Lathe CAM Designer instruction Manual
Denford Mill CAM Designer 2 instruction Manual
Denford Industrial Text Editor Instruction Manual

Denford MIRAC offline programming instruction Manual which includes G Code and M Code descriptions and comprehensive screen displays descriptions.
MIRAC CNC Lathe Installation, Operation and maintenance manual.

Original Denford Technical Brochure.

I can lift the machine onto your transport. It will fit in a large estate car.

OFFERS INVITED.

e-mail: nickbutler@waitrose.com.
Phone: 01483 284114 (Work) and 01483 282627 (Home)

Mad Professor
14-07-2013, 10:41 PM
I will be keeping my eyes on this, but I have a feeling it will be out of my price range.

Nemo1966
17-07-2013, 06:32 PM
I'll give you 100 if you include shipping :witless:

Mad Professor
17-07-2013, 06:36 PM
Nemo1966: I will raise you to 500 CASH, and I will collect it.

Nick Butler: But to be fair I think you should really just list it on eBay, and put the link here.

Nemo1966
17-07-2013, 06:49 PM
600 and Mad Professor Will collect it :whistle:

asto
06-08-2013, 04:33 PM
600 and Mad Professor Will collect it :whistle:
If the machine is running properly I can pay you a thousand pounds.
But...I do not know, is it still available?

regards

asto
06-08-2013, 08:20 PM
600 and Mad Professor Will collect it :whistle:

Hey Nick...your e-mail address <nickbutler@waitrose.com.> returns a message which says this email address is not valid.

Mad Professor
06-08-2013, 08:32 PM
remove the fullstop at the end of his e-mail address and it works fine.

asto
08-08-2013, 12:37 AM
Is that so?
Thanks Mad Professor.

regards

asto
08-08-2013, 12:43 AM
Hey Mad Professor. Do you know if this machine is still available?

cheers

i2i
08-08-2013, 12:48 AM
try ringing one of the numbers.

Mad Professor
08-08-2013, 08:08 AM
I have no idea if the seller still has the item or if it has been sold.

But the contact I had with the seller, he is looking to get 1500-2500 for this unit.

I did point out to the seller, that there was a MIRAC CNC Lathe with ATC that was listed here on mycncuk and was placed on ebay that failed to sell for 1500 back in Feb 2011.

Since then I have not had any more replies from the seller.

asto
08-08-2013, 08:38 PM
I have no idea if the seller still has the item or if it has been sold.

But the contact I had with the seller, he is looking to get 1500-2500 for this unit.

I did point out to the seller, that there was a MIRAC CNC Lathe with ATC that was listed here on mycncuk and was placed on ebay that failed to sell for 1500 back in Feb 2011.

Since then I have not had any more replies from the seller.

...the price of a low mileage preowned car. Looks reasonable. Highly priced this training lathe of the eighties though.

Mad Professor
20-08-2013, 08:41 PM
I can confirm that this has now indeed been SOLD. :joyous:

i2i
21-08-2013, 01:16 AM
I have a denford Cyclone coming up for sale in a couple of weeks, with mach3 conversion.

deisel
21-08-2013, 01:31 PM
may i suggest without getting anyones back up it be made compulsary to add a price to an advert save all this carry on ,1st post and not even back to say its sold,
i was linked to this by a pal when it was first placed as he knows ive been looking for a cnc lathe or a conversion project.not a rant just a suggestion ;)

i2i
21-08-2013, 04:37 PM
may i suggest without getting anyones back up it be made compulsary to add a price to an advert save all this carry on ,1st post and not even back to say its sold,
i was linked to this by a pal when it was first placed as he knows ive been looking for a cnc lathe or a conversion project.not a rant just a suggestion ;)do you fancy a cyclone.?

deisel
21-08-2013, 06:28 PM
No :excitement: Im holding out for an emco or an orac that needs gutting,they come up on occasion im in no rush ;)

i2i
21-08-2013, 09:25 PM
fair enough.:cool:

drumsticksplinter
22-08-2013, 12:20 AM
Probably too rich for my blood, but how much were you looking for on the cyclone?