. .

Home: Lead Screws, Nuts & Supports

General discussion for Lead Screws and Drive Nuts.

Page 1 of 6 123 ... LastLast
Threads 1 to 20 of 107

  1. Ball screw advice

    Started by 333-CNC, 01-03-2021
    • Replies: 4
    • Views: 4,990
    333-CNC
    07-03-2021 Go to last post

  2. Ballscrew Thickness!

    Started by AdCNC, 15-08-2009
    6 Pages •
    1 2 3 ... 6
    ballscrew, thickness 4 Attachment(s)
    • Replies: 51
    • Views: 61,311
    vre
    03-02-2014 Go to last post

  3. What pitch ballscrew would you recommend?

    Started by AdCNC, 05-01-2010
    • Replies: 6
    • Views: 10,449
    AdCNC
    23-02-2010 Go to last post

  4. Low-backlash ball screw recommendations

    Started by Agathon, 13-02-2020
    1 Attachment(s)
    • Replies: 5
    • Views: 8,646
    dazp1976
    17-03-2020 Go to last post

  5. What's a good target for backlash?

    Started by alanambrose, 07-08-2021
    1 Attachment(s)
    • Replies: 5
    • Views: 3,617
    Muzzer
    11-08-2021 Go to last post

  6. NEMA23 mount for BK12

    Started by auhopu, 24-04-2017
    1 Attachment(s)
    • Replies: 2
    • Views: 10,071
    Desertboy
    07-05-2017 Go to last post

  7. Bended ballscrews. What i can do?

    Started by ba99297, 04-06-2014
    3 Pages •
    1 2 3
    7 Attachment(s)
    • Replies: 25
    • Views: 39,667
    komatias
    13-04-2017 Go to last post

  8. Ballscrew machining problem ?

    Started by Bart, 12-06-2015
    2 Attachment(s)
    • Replies: 4
    • Views: 9,871
    Bart
    12-06-2015 Go to last post

  9. Bent ballscrews - is repair possible?

    Started by bee, 07-12-2013
    • Replies: 4
    • Views: 6,893
    bee
    10-12-2013 Go to last post

  10. Ground ballscrew bargain... and a hexapod?!

    Started by bikepete, 19-04-2016
    1 Attachment(s)
    • Replies: 5
    • Views: 16,445
    Boyan Silyavski
    19-04-2016 Go to last post

  11. BK12 end float?

    Started by birchy, 17-07-2013
    2 Pages •
    1 2
    1 Attachment(s)
    • Replies: 15
    • Views: 17,893
    Gytis
    20-07-2013 Go to last post

  12. Driving floating end (ballscrew)

    Started by blackburn mark, 08-09-2010
    2 Pages •
    1 2
    1 Attachment(s)
    • Replies: 16
    • Views: 21,176
    Jonathan
    11-09-2010 Go to last post

  13. Best practice for tight BK12

    Started by bluesking, 13-05-2019
    • Replies: 7
    • Views: 11,403
    routercnc
    24-05-2019 Go to last post

  14. ball bearings in a ball nut, how many?

    Started by bmbaz, 08-12-2014
    2 Pages •
    1 2
    • Replies: 14
    • Views: 32,700
    CaptainBarnacles
    28-01-2020 Go to last post

  15. balscrews from linear motion bearing and rails, question about sizing

    Started by Boyan Silyavski, 18-08-2013
    2 Attachment(s)
    • Replies: 3
    • Views: 30,568
    JAZZCNC
    18-08-2013 Go to last post

  16. Super X1 conversion - Lead Screw Pitch?

    Started by bruce_miranda, 16-09-2008
    conversion, lead, pitch, screw, super
    • Replies: 2
    • Views: 10,197
    Lee Roberts
    19-09-2008 Go to last post

  17. Isel GFM 4433 ballnut preload

    Started by Buckis, 11-10-2021
    1 Attachment(s)
    • Replies: 1
    • Views: 3,516
    the great waldo
    13-10-2021 Go to last post

  18. Angular Contact Bearings for Belt Driven Screws

    Started by CaptainBarnacles, 10-02-2020
    • Replies: 6
    • Views: 6,929
    CaptainBarnacles
    10-02-2020 Go to last post

  19. Stiff 1610 ballscrews, need help.... asap.

    Started by ccmarco, 28-11-2010
    2 Pages •
    1 2
    1 Attachment(s)
    • Replies: 10
    • Views: 10,397
    ccmarco
    05-12-2010 Go to last post

  20. Ball screw fixed end DIY support ideas needed.

    Started by ccmarco, 05-12-2010
    • Replies: 8
    • Views: 11,364
    ccmarco
    06-12-2010 Go to last post
Page 1 of 6 123 ... LastLast

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 15 replies or 150 views
Hot thread with unread posts
More than 15 replies or 150 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Forum Rules