. .

Home: CNCdrive (UC100, UC300ETH)

Discussion for the CNCdrive range of motion controllers, UC300-5LPT, UC400ETH etc.

Page 1 of 2 12 LastLast
Threads 1 to 20 of 27
  1. My MiniGcode creator software

    Started by routercnc, 12-06-2022
    2 Pages
    1 2
    • Replies: 17
    • Views: 3,292
    27-06-2022 Go to last post
  2. My UCCNC Probe Screen version 4 is available now

    Started by A_Camera, 30-06-2021
    3 Pages
    1 2 3
    • Replies: 25
    • Views: 9,077
    03-03-2022 Go to last post
  3. uc300eth vfd connectios

    Started by voyager1972, 02-05-2020
    2 Pages
    1 2
    • Replies: 14
    • Views: 8,718
    01-03-2022 Go to last post
    • Replies: 4
    • Views: 2,033
    08-02-2022 Go to last post
    • Replies: 1
    • Views: 1,234
    07-02-2022 Go to last post
    • Replies: 8
    • Views: 3,110
    23-10-2021 Go to last post
    • Replies: 0
    • Views: 1,404
    16-10-2021 Go to last post
    • Replies: 0
    • Views: 966
    10-09-2021 Go to last post
  4. UC300ETH: UCBB Vs UB1 breakout board ?

    Started by routercnc, 27-08-2021
    3 Pages
    1 2 3
    • Replies: 28
    • Views: 6,901
    30-08-2021 Go to last post
    • Replies: 2
    • Views: 1,559
    28-08-2021 Go to last post
    • Replies: 2
    • Views: 1,398
    26-07-2021 Go to last post
  5. AXBB charge pump fault

    Started by CharlieRam, 11-08-2019
    8 Pages
    1 2 3 ... 8
    • Replies: 78
    • Views: 75,341
    18-07-2021 Go to last post
    • Replies: 4
    • Views: 2,097
    18-07-2021 Go to last post
    • Replies: 4
    • Views: 1,908
    14-07-2021 Go to last post
    • Replies: 21
    • Views: 6,688
    25-04-2021 Go to last post
    • Replies: 2
    • Views: 2,294
    08-04-2021 Go to last post
  6. M$ Antivirus found Trojan in UCCNC

    Started by driftspin, 08-09-2018
    3 Pages
    1 2 3
    • Replies: 26
    • Views: 29,601
    08-02-2021 Go to last post
    • Replies: 64
    • Views: 51,241
    29-01-2021 Go to last post
  7. Question about shielding of cables

    Started by masdo, 29-11-2020
    • Replies: 8
    • Views: 4,420
    29-11-2020 Go to last post
  8. Unusual use of M8/M9 to control a compressor

    Started by ngwagwa, 21-09-2020
    3 Pages
    1 2 3
    • Replies: 20
    • Views: 10,644
    24-09-2020 Go to last post

Page 1 of 2 12 LastLast

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 15 replies or 150 views
Hot thread with unread posts
More than 15 replies or 150 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •