. .

Home: CNCdrive (UC100, UC300ETH)

Discussion for the CNCdrive range of motion controllers, UC300-5LPT, UC400ETH etc.

Page 1 of 2 12 LastLast
Threads 1 to 20 of 27

  1. My MiniGcode creator software

    Started by routercnc, 12-06-2022
    2 Pages •
    1 2
    1 Attachment(s)
    • Replies: 17
    • Views: 23,456
    m_c
    27-06-2022 Go to last post

  2. My UCCNC Probe Screen version 4 is available now

    Started by A_Camera, 30-06-2021
    3 Pages •
    1 2 3
    • Replies: 25
    • Views: 19,511
    A_Camera
    03-03-2022 Go to last post

  3. uc300eth vfd connectios

    Started by voyager1972, 02-05-2020
    2 Pages •
    1 2
    6 Attachment(s)
    • Replies: 14
    • Views: 13,286
    voyager1972
    01-03-2022 Go to last post

  4. Wiring between AXBB-E and Proma THC 150

    Started by JBL_LG, 25-01-2022
    axbb-e, proma thc 150, wiring 1 Attachment(s)
    • Replies: 4
    • Views: 3,959
    JBL_LG
    08-02-2022 Go to last post

  5. Plasma torch doesn't work after connecting Proma THC 150

    Started by JBL_LG, 27-01-2022
    mach3, plasma cutter, proma thc 150
    • Replies: 1
    • Views: 2,927
    JBL_LG
    07-02-2022 Go to last post

  6. Connection between AXBB-E and plasma torch by relay

    Started by JBL_LG, 17-10-2021
    • Replies: 8
    • Views: 5,659
    Kitwn
    23-10-2021 Go to last post

  7. Software similar to RoboDK for AXBB-E

    Started by JBL_LG, 16-10-2021
    • Replies: 0
    • Views: 2,775
    JBL_LG
    16-10-2021 Go to last post

  8. busellato easy jet 7.10 xilog and wave windows 10

    Started by xcelkitchensuk, 10-09-2021
    • Replies: 0
    • Views: 2,584
    xcelkitchensuk
    10-09-2021 Go to last post

  9. UC300ETH: UCBB Vs UB1 breakout board ?

    Started by routercnc, 27-08-2021
    3 Pages •
    1 2 3
    4 Attachment(s)
    • Replies: 28
    • Views: 24,912
    Kitwn
    31-08-2021 Go to last post

  10. Touch Probe and VFD/Spindle Wiring..

    Started by sdimelow, 27-08-2021
    spindle, ub1, uc300eth, vfd, wiring 3 Attachment(s)
    • Replies: 2
    • Views: 3,628
    sdimelow
    28-08-2021 Go to last post

  11. 2nd opinion on Wiring diagram.. proximity - isolation - lpt.

    Started by dazp1976, 26-07-2021
    1 Attachment(s)
    • Replies: 2
    • Views: 2,864
    dazp1976
    26-07-2021 Go to last post

  12. AXBB charge pump fault

    Started by CharlieRam, 11-08-2019
    8 Pages •
    1 2 3 ... 8
    22 Attachment(s)
    • Replies: 78
    • Views: 94,469
    dazp1976
    18-07-2021 Go to last post

  13. UCCNC Modbus Master plugin..cant gete my VFD to run ????

    Started by eskolin, 13-06-2021
    7 Attachment(s)
    • Replies: 4
    • Views: 4,026
    A_Camera
    18-07-2021 Go to last post

  14. Brain transplant - swapping ESS for UC300ETH

    Started by Neale, 11-06-2021
    • Replies: 4
    • Views: 3,523
    A_Camera
    14-07-2021 Go to last post

  15. Do I need a BoB when replacing a parallel port connection with a UC300 or UC400?

    Started by ian823478, 11-03-2021
    3 Pages •
    1 2 3
    6 Attachment(s)
    • Replies: 21
    • Views: 10,378
    dazp1976
    25-04-2021 Go to last post

  16. Modbus monitoring and control using UCCNC

    Started by A_Camera, 07-04-2021
    1 Attachment(s)
    • Replies: 2
    • Views: 4,128
    A_Camera
    08-04-2021 Go to last post

  17. M$ Antivirus found Trojan in UCCNC

    Started by driftspin, 08-09-2018
    3 Pages •
    1 2 3
    • Replies: 26
    • Views: 35,900
    AndyGuid
    08-02-2021 Go to last post

  18. The Dreaded X axis stepper error using UC400ETH and UCCNC !!!

    Started by dachopper, 25-07-2017
    7 Pages •
    1 2 3 ... 7
    9 Attachment(s)
    • Replies: 64
    • Views: 64,905
    JoelDar
    29-01-2021 Go to last post

  19. Question about shielding of cables

    Started by masdo, 29-11-2020
    • Replies: 8
    • Views: 7,363
    JAZZCNC
    29-11-2020 Go to last post

  20. Unusual use of M8/M9 to control a compressor

    Started by ngwagwa, 21-09-2020
    3 Pages •
    1 2 3
    5 Attachment(s)
    • Replies: 20
    • Views: 14,792
    ngwagwa
    24-09-2020 Go to last post
Page 1 of 2 12 LastLast

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 15 replies or 150 views
Hot thread with unread posts
More than 15 replies or 150 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Forum Rules