. .
Tab Content
  • Doddy's Avatar
    55 Minutes Ago
    Jazz answered your question perfectly. But I'll answer with another question. How are you going to interface the UC300eth with the servo? The thought...
    9 replies | 8922 view(s)
  • Doddy's Avatar
    1 Day Ago
    The UC100 is a respected device. Be aware there's a grey market out there with fake UC100s - obviously the horse has bolted here, but just go into...
    18 replies | 1438 view(s)
  • Doddy's Avatar
    2 Days Ago
    Doddy replied to a thread Triac PC Linuxcnc in Denford Mills
    The copy of the manual I found online suggest pin 61 is a +12V (10mA max) regulated supply. Check that is +12V wrt the common rail (99.9% convinced...
    21 replies | 4692 view(s)
  • Doddy's Avatar
    2 Days Ago
    Doddy replied to a thread Triac PC Linuxcnc in Denford Mills
    If you was to write a pot on the spindle controller, you should have 3 pins on the spindle controller to attach to, what are those? Likely a good...
    21 replies | 4692 view(s)
  • Doddy's Avatar
    2 Days Ago
    Doddy replied to a thread Triac PC Linuxcnc in Denford Mills
    From what I squinted at with that particular board the circuitry was visible separate from the LV and HV sides. You’d supply the LV from the general...
    21 replies | 4692 view(s)
  • Doddy's Avatar
    2 Days Ago
    Doddy replied to a thread Triac PC Linuxcnc in Denford Mills
    John, I've looked at the link to that board and I can't work it out - but it looks probable (PCB underside image) that the 0V reference for the 0-10V...
    21 replies | 4692 view(s)
  • Doddy's Avatar
    1 Week Ago
    Though I'd be exploring the bullet on the S 720 feature list...
    18 replies | 1438 view(s)
  • Doddy's Avatar
    1 Week Ago
    303 Euros?? I'd concur with the earlier recommendations of the UCxx hardware.
    18 replies | 1438 view(s)
  • Doddy's Avatar
    1 Week Ago
    Doddy replied to a thread Triac PC Linuxcnc in Denford Mills
    Certainly can be made to work, however, bear in mind the switching time for the relay(s) - guessing in the order of 5-10ms (I'll let you do the math...
    21 replies | 4692 view(s)
  • Doddy's Avatar
    1 Week Ago
    Doddy replied to a thread Triac PC Linuxcnc in Denford Mills
    Without data sheet (I've googled for 5 minutes and given up to watch the F1 qualifying instead) - and without knowing the sensor supply voltage...
    21 replies | 4692 view(s)
  • Doddy's Avatar
    4 Weeks Ago
    Doddy replied to a thread Air flow in General Discussion
    If you don't mind, can you advise compressor model?, also, can this run/provide cooling continuously (say 1hr+.... I know that's probably short for...
    16 replies | 2121 view(s)
No More Results
About Doddy

Basic Information

About Doddy
City:
Preston
Country:
United Kingdom

Statistics


Total Posts
Total Posts
1,344
Posts Per Day
0.43
Last Post
How to setup Chinese AASD Servo electronic gearing 55 Minutes Ago
Total Thanks
Total Thanks
64
General Information
Last Activity
52 Minutes Ago
Current Activity
Viewing Thread NEW MEMBER: New User from Italy
Join Date
29-12-2013
Referrals
1

1 Friend

Showing Friends 1 to 1 of 1