Find latest postsMini Statistics
- Join Date
- 07-01-2018
- Last Activity
- 6 Days Ago
- Avatar
Recent Visitors
- Andrewg,
- clutchslip,
- Doddy,
- JimJam,
- komatias,
- m.i.k.e,
- MikeInDevon,
- m_c,
- NB70,
- V8kid
- Tab Content
- Muzzer's Activity
- About Me
- Video Library
-
Older Activity
-
6 Days AgoHaha yes I've had a similar scare a couple of times where I've nudged the handwheel when it's been sitting on my bench or the machine table,...15 replies | 865 view(s) -
1 Week AgoI have an XHC PHB04B-4 wireless MPG in my Centroid Acorn system and I've never had a problem with interference. The closest I've had is loss of...15 replies | 865 view(s)
-
1 Week AgoI believe Andy Pugh on the LinuxCNC forum fitted 2 MPGs on the apron of his original lathe conversion but IIRC he says he never used them. As noted,...15 replies | 865 view(s)
-
2 Weeks AgoMuzzer replied to a thread Myford super 7 lathe, tripping RCD in Lathes, Lathe Rebuilding & ConversionsStep by step - disconnect the motor wiring (insulating them carefully) and see if the RCD still trips. If not, it suggests the motor insulation may...1 replies | 289 view(s)
-
3 Weeks AgoMuzzer replied to a thread NEW MEMBER: Very excited to get started with cnc! Hello by the way. in New Member IntroductionsI wouldn't give up on Fusion yet. It's still a great bit of software, even the free version which actually has most of the features you'd ever need...9 replies | 624 view(s)
-
3 Weeks AgoTry Google Translate - I assume that's what Jazz is referring to. When you select the camera icon, it will recognise and translate any Chinese...21 replies | 2447 view(s)
-
3 Weeks AgoYou can do just as good a job translating the document yourself as they would. After all, they just use Baidu Translate themselves, which is very...21 replies | 2447 view(s)
-
3 Weeks AgoI had large cast iron wheels like that on my Bridgeport. I couldn't get a decent response from the DMM servos until I removed them. Their moment of...30 replies | 2786 view(s)
-
4 Weeks AgoPerhaps an SCR drive then, as SCRs don't have a 30V threshold on them. But even so, the market for diacs is very limited these days. What's it...30 replies | 2786 view(s)
-
4 Weeks AgoYes, I remember them. Presumably used in the gate of a triac or scr, then. That dates the controller, as that threshold function has been built into...30 replies | 2786 view(s)
-
4 Weeks AgoYes, usually the combination of the limited number of nominal voltages and the tolerance. They aren't too bad actually but you may struggle to find a...30 replies | 2786 view(s)
-
4 Weeks AgoYou can even use a hysteretic controller where the switch turns on above a high threshold and stays on until it falls to a low threshold. Can be...30 replies | 2786 view(s)
-
4 Weeks AgoNo, I'm thinking of the "chopping / braking resistor" concept. Acts like a giant zener diode. Usually they have a switching transistor and a low...30 replies | 2786 view(s)
-
4 Weeks AgoThe best solution for these low voltage drives would be a regulated (switched mode) power supply combined with a clamp circuit. That way you could...30 replies | 2786 view(s)
About Muzzer
Basic Information
About Muzzer
- City:
- Lytham St. Annes
- Country:
- United Kingdom
Statistics
Total Posts
- Total Posts
- 264
- Posts Per Day
- 0.24
- Last Post
- Hand feed XYZ cube 6 Days Ago
Total Thanks
- Total Thanks
- 5
General Information
- Last Activity
- 6 Days Ago
- Join Date
- 07-01-2018
- Referrals
- 0
Newbie