- Tab Content
- dazp1976's Activity
- About Me
- Video Library
-
Older Activity
-
6 Days Agodazp1976 replied to a thread Panasonic MSD043Axxx Servo Driver pin outs???? in Motor Drivers & ControllersAs in the 'plug-in to the drive' side is configured as long rows...... The solder tabs on the back 'cable side' are configured as the diagram. ...22 replies | 1150 view(s)
-
1 Week Agodazp1976 replied to a thread Panasonic MSD043Axxx Servo Driver pin outs???? in Motor Drivers & ControllersTake a detailed photo of the front of the drive itself showing the connection. I did find part number: 10136-3000VE. Connector. 10336-52A0-008....22 replies | 1150 view(s)
-
1 Week AgoYes, spindle. I didn't think it was worth the bother. Thought I'd ask the pro anyway. The tool change idea sounds a good one. Ta.21 replies | 1378 view(s)
-
1 Week AgoQuestion. Talking of switching drive directions: Servo drive. I'm using a small opto module to switch the digital input on/off for cw/ccw - m3/m4. ...21 replies | 1378 view(s)
-
1 Week Agodazp1976 replied to a thread Panasonic MSD043Axxx Servo Driver pin outs???? in Motor Drivers & ControllersThe attachment not working for me. I added a couple of examples in my previous post. I don't know whether you'd need male/female. You'll have to...22 replies | 1150 view(s)
-
1 Week Agodazp1976 replied to a thread Panasonic MSD043Axxx Servo Driver pin outs???? in Motor Drivers & ControllersA bit like this one which is a db44 for a delta. https://www.aliexpress.com/item/1005002086435849.html?spm=a2g0o.cart.0.0.666b3c00PlsAmK&mp=1 The...22 replies | 1150 view(s)
-
1 Week AgoI'm not that "fool"ish then, yes?. I tend to use optocoupler modules instead of relays for switching DC components lately. Can get them for peanuts.21 replies | 1378 view(s)
-
1 Week AgoHey. I'm only going on what someone else did and broke their axbb-e. The bbe is basically the 300eth and a smaller ucbb. So :tongue: Edit:...21 replies | 1378 view(s)
-
1 Week AgoIt's been done on another forum a while back. Directly connected it and broke the axbb-e. Had to replace it. May have done it wrong in first...21 replies | 1378 view(s)
-
1 Week AgoYou need to. Or any other kind of 'switch'. You can't directly connect a breakout board / controller output to vfd FWD / DCOM. It simply does not...21 replies | 1378 view(s)
-
1 Week AgoYou can use Dupont 2.54mm wires/ connectors directly on the UC300eth IDC pins. VFD FOR - DCM is just a ground sinking line. External relay (or opto...21 replies | 1378 view(s)
-
2 Weeks AgoNowhere does. GB is going to the dogs!10 replies | 1459 view(s)
-
2 Weeks AgoIf Boxford aren't helpful at all, you may need to look at converting elecs etc over to Mach3 or 4 or uccnc. It's been done many times before, just...2 replies | 1428 view(s)
-
3 Weeks Agodazp1976 replied to a thread Slide lubricant, bad alignment or not enough torque ? in General DiscussionWith the inductance on those steppers, they need DM860 drives and minimum 60v to get decent high rapid speeds. Proven. But, never any issue on 36v...20 replies | 1807 view(s)
-
3 Weeks Agodazp1976 replied to a thread Slide lubricant, bad alignment or not enough torque ? in General DiscussionGT85 Teflon spray all day long for cleaning metal to metal surface slides. I used to run automated equipment from Heidelberg machinery and they...20 replies | 1807 view(s)
-
3 Weeks Agodazp1976 replied to a thread Slide lubricant, bad alignment or not enough torque ? in General DiscussionNope. Only with the right voltage. However, if you can't get up to at least 1000mm/min with it then something is definately wrong. What speed are...20 replies | 1807 view(s)
-
3 Weeks AgoI've kind of been ordering nearly everything I want from Aliexpress lately. Been no longer than 2 weeks everytime. I find a lot of the stuff you...14 replies | 12339 view(s)
About dazp1976
Basic Information
About dazp1976
- City:
- coventry
- Country:
- United Kingdom
Statistics
Total Posts
- Total Posts
- 387
- Posts Per Day
- 0.28
- Last Post
- Panasonic MSD043Axxx Servo Driver pin outs???? 6 Days Ago
Total Thanks
- Total Thanks
- 0
General Information
- Last Activity
- 6 Hours Ago
- Join Date
- 18-08-2018
- Referrals
- 0
CO2 laser for cutting beech