Voicecoil
Find latest postsMini Statistics
- Join Date
- 26-08-2018
- Last Activity
- 2 Days Ago
- Avatar
Recent Visitors
- EZELab,
- f750,
- grain_r,
- Lee Roberts,
- mortenl,
- naattila,
- Nealieboyee,
- ngwagwa,
- RichardR,
- the great waldo
- Tab Content
- Voicecoil's Activity
- About Me
- Video Library
-
Older Activity
-
2 Days AgoVoicecoil replied to a thread Lathe recommendations for turning tungsten darts. in Machine DiscussionWould copper tungsten be a better material to use? The high tungsten variants have similar density to tungsten carbide (WC !) and I'm told it's a lot...7 replies | 406 view(s)
-
4 Days AgoThanks for the advice. BTW, what diameter cutters were you using please? - it would be useful to get an idea of a workable SFM.10 replies | 1025 view(s)
-
1 Week AgoThanks for those leads. It's not clear exactly what the TroGlass stuff is from how their description reads to me, might give them a ring tomorrow to...3 replies | 383 view(s)
-
1 Week AgoI've had similar experiences - unless it's a matter of poor heatsinking and the LED chips getting too hot it seems to be the PSU's that fail most...7 replies | 495 view(s)
-
1 Week AgoI'm after some black/clear or black/translucent engraving sheet (ideally 1.6mm) to make a couple of custom speedo dials - does anyone know of a...3 replies | 383 view(s)
-
1 Week AgoVoicecoil replied to a thread BUILD LOG: El Beast - Initial design phase, comments and critique welcomed! in DIY Router Build LogsLooking at the link I would guess it should be in the Manufacturer's News section???403 replies | 296576 view(s)
-
1 Week AgoIf you had >15mm it might have been possible to fit a low-ish profile bellows cover in there, but with only 6mm that's not going to happen. The only...4 replies | 465 view(s)
-
1 Week AgoHow much clearance is there between the back of the spindle and the top/bottom plates of the Z-axis assembly? And what's the total Z travel?4 replies | 465 view(s)
-
2 Weeks AgoVoicecoil replied to a thread Which solution is best for a small CNC router in Gantry/Router Machines & BuildingIt looks like you have the opportunity to bolt through from the horizontal carriage plate to the bottom of the gantry extrusion - this will greatly...4 replies | 854 view(s)
-
3 Weeks AgoI ended up using GX20 connectors - not quite so easy to find, but very similar and they have a bit bigger cable inlet size, which I found useful when...16 replies | 854 view(s)
-
3 Weeks AgoVoicecoil replied to a thread SFU1605 Ballscrew Standard vs Anti-backlash in Lead Screws, Nuts & SupportsBallnuts (assuming they're of reasonable quality) on a ballscrew inherently have very low backlash. Since they work on a rolling rather than sliding...5 replies | 557 view(s)
About Voicecoil
Basic Information
About Voicecoil
- City:
- South Lakeland
- Country:
- United Kingdom
- Occupation:
- Engineer & Pyrotechnician
Statistics
Total Posts
- Total Posts
- 518
- Posts Per Day
- 0.59
- Last Post
- Lathe recommendations for turning tungsten darts. 2 Days Ago
Total Thanks
- Total Thanks
- 11
General Information
- Last Activity
- 2 Days Ago
- Join Date
- 26-08-2018
- Referrals
- 0
Hi Everyone - Newbie wanting to...