. .
Tab Content
  • Doddy's Avatar
    15 Hours Ago
    Doddy replied to a thread Triac PC Linuxcnc in Denford Mills
    The copy of the manual I found online suggest pin 61 is a +12V (10mA max) regulated supply. Check that is +12V wrt the common rail (99.9% convinced...
    see more
    21 replies | 4544 view(s)
  • Doddy's Avatar
    23 Hours Ago
    Doddy replied to a thread Triac PC Linuxcnc in Denford Mills
    If you was to write a pot on the spindle controller, you should have 3 pins on the spindle controller to attach to, what are those? Likely a good...
    see more
    21 replies | 4544 view(s)
  • Doddy's Avatar
    1 Day Ago
    Doddy replied to a thread Triac PC Linuxcnc in Denford Mills
    From what I squinted at with that particular board the circuitry was visible separate from the LV and HV sides. You’d supply the LV from the general...
    see more
    21 replies | 4544 view(s)
  • Doddy's Avatar
    1 Day Ago
    Doddy replied to a thread Triac PC Linuxcnc in Denford Mills
    John, I've looked at the link to that board and I can't work it out - but it looks probable (PCB underside image) that the 0V reference for the 0-10V...
    see more
    21 replies | 4544 view(s)
  • Doddy's Avatar
    1 Week Ago
    Doddy replied to a thread Connecting my High-Z-S 720 in Heiz CNC Routers
    Though I'd be exploring the bullet on the S 720 feature list...
    see more
    15 replies | 1216 view(s)
  • Doddy's Avatar
    1 Week Ago
    Doddy replied to a thread Connecting my High-Z-S 720 in Heiz CNC Routers
    303 Euros?? I'd concur with the earlier recommendations of the UCxx hardware.
    see more
    15 replies | 1216 view(s)
  • Clive S's Avatar
    1 Week Ago
    Clive S replied to a thread Connecting my High-Z-S 720 in Heiz CNC Routers
    I think Jazzcnc also stocks controllers in the UK. https://www.jazzcnc.co.uk/motion-control
    see more
    15 replies | 1216 view(s)
  • Doddy's Avatar
    1 Week Ago
    Doddy replied to a thread Triac PC Linuxcnc in Denford Mills
    Certainly can be made to work, however, bear in mind the switching time for the relay(s) - guessing in the order of 5-10ms (I'll let you do the math...
    see more
    21 replies | 4544 view(s)
  • Doddy's Avatar
    1 Week Ago
    Doddy replied to a thread Triac PC Linuxcnc in Denford Mills
    Without data sheet (I've googled for 5 minutes and given up to watch the F1 qualifying instead) - and without knowing the sensor supply voltage...
    see more
    21 replies | 4544 view(s)
  • Clive S's Avatar
    1 Week Ago
    Clive S replied to a thread Annoying issue with my cnc router in Machine Discussion
    Have you checked for a broken connection at the spindle or somewhere along the cable where it gets a lot of flex
    see more
    4 replies | 726 view(s)
  • Doddy's Avatar
    3 Weeks Ago
    Doddy replied to a thread Air flow in General Discussion
    If you don't mind, can you advise compressor model?, also, can this run/provide cooling continuously (say 1hr+.... I know that's probably short for...
    see more
    16 replies | 2097 view(s)
No More Results
About depronman

Basic Information

About depronman
City:
St Annes on the Sea
Country:
United Kingdom

Statistics


Total Posts
Total Posts
159
Posts Per Day
0.12
Last Post
Denford cyclone conversion 21-05-2022
Total Thanks
Total Thanks
6
General Information
Last Activity
2 Hours Ago
Join Date
01-11-2018
Referrals
0

4 Friends

Showing Friends 1 to 4 of 4