- Tab Content
- Patcho1961's Activity
- About Me
- Video Library
- Tab Content
-
Older Activity
-
6 Days AgoPatcho1961 replied to a thread NEW MEMBER: New guy finishing off a mini mill build in New Member Introductionsit could be some of the problem Doddy, but i can see the same pattern in this acrylic test, same settings just different material. But all in all...42 replies | 3595 view(s)
-
6 Days AgoPatcho1961 replied to a thread NEW MEMBER: New guy finishing off a mini mill build in New Member Introductionsnew uc300 ethernet card and breakout board wired in new Z ball screw and nut fitted, when i say fitted i still have to put in the other 4 cap...42 replies | 3595 view(s)
-
6 Days AgoPatcho1961 replied to a thread NEW MEMBER: New guy finishing off a mini mill build in New Member Introductionsfirst attempt cutting ally, 1mm deep cut with 3mm end mil, 50mm diameter circle, you can see from the pattern left by the cutter i have some backlash...42 replies | 3595 view(s)
-
6 Days AgoPatcho1961 replied to a thread NEW MEMBER: New guy finishing off a mini mill build in New Member Introductions42 replies | 3595 view(s)
-
1 Week AgoPatcho1961 replied to a thread NEW MEMBER: New guy finishing off a mini mill build in New Member IntroductionsI will take pics today, apologies didn't realise I had to produce photographic evidence to support my claims of success lol42 replies | 3595 view(s)
-
1 Week AgoPatcho1961 replied to a thread NEW MEMBER: New guy finishing off a mini mill build in New Member IntroductionsOK cnc people, Just an update on where I am at with my mill I have fitted a new ball nut to the z, turned out there where no balls in the nut on...42 replies | 3595 view(s)
-
2 Weeks AgoPatcho1961 replied to a thread NEW MEMBER: New guy finishing off a mini mill build in New Member IntroductionsJazz I have no problem machining them, I have a pretty well sorted workshop at work and I am fully capable of machining any bearing blocks required...42 replies | 3595 view(s)
-
2 Weeks AgoPatcho1961 replied to a thread NEW MEMBER: New guy finishing off a mini mill build in New Member Introductionsindeed it is sods law! I can't be waiting 3 weeks any where in the uk to get something decent? i have been looking at motion control products in...42 replies | 3595 view(s)
-
2 Weeks AgoPatcho1961 replied to a thread NEW MEMBER: New guy finishing off a mini mill build in New Member IntroductionsJazz wish you had said earlier, I ordered UC300ETH + UCSB BoB with cables and UCCNC license from CNCDRIVE on saturday and sent money transfer this...42 replies | 3595 view(s)
-
2 Weeks AgoPatcho1961 replied to a thread NEW MEMBER: New guy finishing off a mini mill build in New Member IntroductionsOK people, swapped out my BoB and yay, limit switches and E-stop all working fine. Will spend next week tweaking and I think I might have to do some...42 replies | 3595 view(s)
-
3 Weeks AgoPatcho1961 replied to a thread NEW MEMBER: New guy finishing off a mini mill build in New Member IntroductionsThanks doddy, I am planning to swap out the BoB tomorrow, I think I have found the right data sheet for it, it appears to have the ability to have...42 replies | 3595 view(s)
-
-
3 Weeks AgoPatcho1961 replied to a thread NEW MEMBER: New guy finishing off a mini mill build in New Member Introductionsscreen removed (screw driver worked) pics in album of naked BoB, back of BoB and removed screen42 replies | 3595 view(s)
-
3 Weeks AgoPatcho1961 replied to a thread NEW MEMBER: New guy finishing off a mini mill build in New Member Introductionsi will endeavour to remove the offending screen, my first ry will be with a screw driver if that does not work i will resort to a hammer. i do have...42 replies | 3595 view(s)
-
3 Weeks AgoPatcho1961 replied to a thread NEW MEMBER: New guy finishing off a mini mill build in New Member IntroductionsI have set up an album in my profile with a few pictures in it, made it public so hopfully you guys can view it steve42 replies | 3595 view(s)
-
-
3 Weeks AgoPatcho1961 replied to a thread NEW MEMBER: New guy finishing off a mini mill build in New Member IntroductionsOh and one other thing - i believe i have to post at least 10 times before i can post pictures, but i am trying to think of ten things to say so i...42 replies | 3595 view(s)
-
3 Weeks AgoPatcho1961 replied to a thread NEW MEMBER: New guy finishing off a mini mill build in New Member IntroductionsOk people i will try and answer some of the questions and i do understand that trying to fault find with little information is difficult and somewhat...42 replies | 3595 view(s)
-
3 Weeks AgoPatcho1961 replied to a thread NEW MEMBER: New guy finishing off a mini mill build in New Member IntroductionsThe mill and parts were purchased from a model maker who didn't manage to finish the mill conversion, but I agree the copy of mach3 supplied could...42 replies | 3595 view(s)
-
3 Weeks AgoPatcho1961 replied to a thread NEW MEMBER: New guy finishing off a mini mill build in New Member IntroductionsThanks for all the replies and information, i kinda get the idea mach 3/4 is dead and we have all moved on . . lol I have had a look at all of the...42 replies | 3595 view(s)
-
4 Weeks AgoPatcho1961 started a thread NEW MEMBER: New guy finishing off a mini mill build in New Member IntroductionsHi everyone, I am a toolmaker and have some experience in using cnc machines, but have decided to build a small cnc mill for fun really. I'm not...42 replies | 3595 view(s)
About Patcho1961
Basic Information
About Patcho1961
- City:
- Surrey
- Country:
- United Kingdom
Statistics
Total Posts
- Total Posts
- 19
- Posts Per Day
- 0.45
- Last Post
- New guy finishing off a mini mill build 6 Days Ago
Albums
- Total Albums
- 1
- Total Photos
- 9
Total Thanks
- Total Thanks
- 2
General Information
- Last Activity
- 1 Day Ago
- Join Date
- 17-01-2021
- Referrals
- 0
A little clear out