- Tab Content
- Mammers's Activity
- About Me
- Video Library
-
Older Activity
-
10 Hours AgoThis is really cool- thanks so much for sharing! Very inspiring24 replies | 5583 view(s)
-
1 Day AgoMammers replied to a thread NEW MEMBER: Trained monkey looking to level up! in New Member IntroductionsRecently just did this as per your and m_c's recommendation, couldn't be happier with how it worked out. Thanks so much.14 replies | 1183 view(s)
-
2 Days AgoThat's really interesting, I've never heard of GRBL. The amount of open-source stuff out there genuinely boggles my mind sometimes. What a time to be...17 replies | 1190 view(s)
-
2 Days AgoThanks for replying anyway- that's definitely the number 1 cause of headache for this particular issue, from what I've been reading online. If anyone...17 replies | 1190 view(s)
-
3 Days AgoThank you to everyone who took the time to read and provide some advice- it is much appreciated After much head-scratching, crying and pleading we...17 replies | 1190 view(s)
-
5 Days AgoReally appreciate your input m_c. I've attached an image I have to hand of the inside of the control box, I can get a better one when I'm in the...17 replies | 1190 view(s)
-
6 Days AgoI'm having zero luck with this. I've flicked through all the modes for the PP in the bios and tried each The port address is definitely...17 replies | 1190 view(s)
-
1 Week AgoThanks m_c , I'll have a mooch and report back. I'm fairly sure I've been through the BIOS and wanjangled all that, but it's best I double check and...17 replies | 1190 view(s)
-
1 Week AgoHi Talha222 - yes it's 32bit17 replies | 1190 view(s)
-
1 Week AgoThe estop light on the control box does go off momentarily during PC startup, and I managed to get it to go off by pressing movement keys in a...17 replies | 1190 view(s)
-
1 Week AgoHi m_c, yes it's 32 bit. Very strange.17 replies | 1190 view(s)
-
1 Week AgoAs luck would have it, my Windows XP PC blew up. I managed to source a Windows 7 PC with a parallel port, install mach3 and transfer over my config...17 replies | 1190 view(s)
-
1 Week AgoMammers replied to a thread NEW MEMBER: Trained monkey looking to level up! in New Member IntroductionsExcellent, thanks for that14 replies | 1183 view(s)
-
1 Week AgoMammers replied to a thread NEW MEMBER: Trained monkey looking to level up! in New Member IntroductionsHopefully one day I can be where you're at :eagerness: It is our only machine, so we do rely fairly heavily on it. We're not so busy that any...14 replies | 1183 view(s)
-
1 Week AgoMammers replied to a thread NEW MEMBER: Trained monkey looking to level up! in New Member IntroductionsThat sounds like a winner, thanks for sharing your experience14 replies | 1183 view(s)
-
1 Week AgoMammers replied to a thread NEW MEMBER: Trained monkey looking to level up! in New Member IntroductionsThat's really helpful, I'll certainly look into this aswell. Thank you.14 replies | 1183 view(s)
-
2 Weeks AgoMammers replied to a thread NEW MEMBER: Trained monkey looking to level up! in New Member IntroductionsThanks m_c. We're pootling along just fine at the moment, but you are right: there is the ever-present worry of PC failure and lack of parts. We've...14 replies | 1183 view(s)
-
2 Weeks AgoMammers replied to a thread NEW MEMBER: Trained monkey looking to level up! in New Member IntroductionsHi m_c, thanks for taking the time to read and respond! :adoration: I'm fairly sure I have backups, I'll double-check. Regarding the control box-...14 replies | 1183 view(s)
-
2 Weeks AgoMammers started a thread NEW MEMBER: Trained monkey looking to level up! in New Member IntroductionsHi there! I've been lurking for a little while and scratching my head, I just figured I'd come and say hello :monkey: I've been using a 3 axis...14 replies | 1183 view(s)
About Mammers
Basic Information
About Mammers
- City:
- North West
- Country:
- United Kingdom
- Biography:
- Trained monkey hoping to move on from screeching and smashing buttons to learning more about CNC
Statistics
Total Posts
- Total Posts
- 19
- Posts Per Day
- 1.32
- Last Post
- Diy concrete cnc 10 Hours Ago
Total Thanks
- Total Thanks
- 7
General Information
- Last Activity
- 2 Hours Ago
- Join Date
- 18-01-2023
Diy concrete cnc