- Tab Content
- dudz's Activity
- About Me
- Friends
- Video Library
-
Older Activity
-
5 Hours AgoWell, you are in a funny place with this machine and heading on a potentially slippery slope.? There is no easy way to say this so I'll just say it.!...2 replies | 126 view(s)
-
2 Days AgoJust use the widest cutter you have and write a bit of code to make test cuts for both directions on a piece of scrap then adjust as required,...1 replies | 222 view(s)
-
4 Days AgoJAZZCNC replied to a thread How to setup Chinese AASD Servo electronic gearing in Machine DiscussionDazp suggests a good board because the UB1 is an excellent choice if you are using servos due to the fact its differential line drivers are nice and...12 replies | 9358 view(s)
-
4 Days AgoOK, but how do you expect us to give you meaningful help if you are showing pics that don't match how you have it set up.? My suggestion is that...5 replies | 343 view(s)
-
5 Days AgoJAZZCNC replied to a thread How to setup Chinese AASD Servo electronic gearing in Machine DiscussionThe 400Khz is per axis output.12 replies | 9358 view(s)
-
5 Days AgoProbably because you are using the wrong Port.? Port #1 which you are using is mostly Inputs, Port #2 and #3 are the ones with all the outputs on...5 replies | 343 view(s)
-
5 Days AgoYour welcome, This offer also goes to anyone else who is lurking in the background and thinking about getting into CNC but is unsure of what's...3 replies | 432 view(s)
-
6 Days AgoOk, That's a shame and it will most likely perform ok, but that doesn't mean it's a good choice.! Also, let me just point out that it's a common...18 replies | 1684 view(s)
-
1 Week AgoMach3 is a bad choice, it's unsupported and does have some bugs which won't ever get fixed. UCCNC is far better software that is supported and made...18 replies | 1684 view(s)
-
1 Week AgoHello, iestyn, If you want to take a trip across to Goole you are very welcome to come to visit our Workshop and I will give you a crash course...3 replies | 432 view(s)
-
3 Weeks AgoJAZZCNC replied to a thread ATC spindle pushes toolholder when the drawbar is released in Machine DiscussionNot a dumb question but not how it works. The Drawbar clamp which grabs the pull stud is pulled against a taper machined into the spindle shaft...3 replies | 891 view(s)
-
3 Weeks AgoJAZZCNC replied to a thread ATC spindle pushes toolholder when the drawbar is released in Machine Discussion#1 Very likely be you have the wrong pull stud or the wrong holders. BT30 and ISO30 look the same but they are very slightly different. #2 Yes you...3 replies | 891 view(s)
About dudz
Basic Information
- Age
- 52
About dudz
- City:
- Dunedin
- Country:
- New Zealand
- Interests:
- Building. Motorcycles.
- Occupation:
- Electrician
Signature
3 axis CNC/router / Alu profile frame....25mm Alu Cutting bed X=500mm Y=300mm Z=110mm.....Supported 25mm X rails ....Supported 20mm Y rails....Supported 20mm Z rails.....2.2kw Chinese WC spindle..... CSLAB CSMIO/IP-M 4-axis Ethernet Motion Controller....M542 Drivers..SY60STH86-3008BF Motors...running....Mach3 / Cambam / Emachineshop.
Contact
Instant Messaging
Send an Instant Message to dudz Using...
-
Skype™ dudz669
Statistics
Total Posts
- Total Posts
- 273
- Posts Per Day
- 0.08
- Last Post
- Back after a few years ... Mach3 Question please 18-04-2022
Albums
- Total Albums
- 1
- Total Photos
- 5
Total Thanks
- Total Thanks
- 69
General Information
- Last Activity
- 21-04-2022
- Join Date
- 17-10-2012
- Referrals
- 0
Help, FoxAlien motor upgrade