Find latest posts
- Tab Content
- Clive S's Activity
- About Me
- Friends
- Video Library
-
Older Activity
-
2 Days AgoClive S replied to a thread Aluminium Profile Type Router - Initial questions in Gantry/Router Machines & BuildingWhat you MUST NOT do is connect anything to the bolt on the top side that is connected back to the chassis as that would then make a shorted turn. ...56 replies | 8848 view(s) -
2 Days AgoClive S replied to a thread Generic Chinese VFD, XSY-AT1 Programming Parameters/Settings in Spindles & Drive MotorsThis is from the link you posted...15 replies | 6988 view(s)
-
3 Days AgoClive S replied to a thread Generic Chinese VFD, XSY-AT1 Programming Parameters/Settings in Spindles & Drive MotorsDo you have the manual for it. Also did you have the spindle connected? A picture of the terminals would help15 replies | 6988 view(s)
-
3 Days AgoClive S replied to a thread Suggested PWM frequency for a minimal Novamill conversion in Denford MillsI have done a conversion on a Novamill using a Mesa 7i92. I also changed the feed and speed pots to alps encoders. Here is a link for some pics...5 replies | 302 view(s)
-
6 Days AgoClive S replied to a thread mach3 wont reset keeps saying external emg stop requested in Boxford LathesPlus one :thumsup:49 replies | 2863 view(s)
-
1 Week AgoClive S replied to a thread mach3 wont reset keeps saying external emg stop requested in Boxford LathesSorry I just don't see the point. all you are doing is just burning electricity up and putting heat into to the control box49 replies | 2863 view(s)
-
1 Week AgoClive S replied to a thread mach3 wont reset keeps saying external emg stop requested in Boxford LathesHere you go:-...49 replies | 2863 view(s)
-
1 Week AgoClive S replied to a thread mach3 wont reset keeps saying external emg stop requested in Boxford LathesYes. If you get them the wrong way round it will just measure -ve. make sure the meter is set to DC and AC for the mains side. Be careful . ...49 replies | 2863 view(s)
-
1 Week AgoClive S replied to a thread mach3 wont reset keeps saying external emg stop requested in Boxford LathesGeoff. Do you have a DVM ? a meter to test the voltage AC and DC . If so can you check what voltage you are getting from each PSU on the DC...49 replies | 2863 view(s)
-
1 Week AgoWell you are not helping yourself. If you can't be bothered to answer the questions I can't either.10 replies | 773 view(s)
-
1 Week AgoYou need to give more info. What says the timber is 200x120 and what size should it be? what cad and cam are you using10 replies | 773 view(s)
-
1 Week AgoClive S replied to a thread mach3 wont reset keeps saying external emg stop requested in Boxford LathesPSU = power supply. Also check if you have 5V as it seems you have a usb providing that and some usb's don't supply enough current. As Jazz says...49 replies | 2863 view(s)
-
1 Week AgoHi, I would try a compression bit/cutter, their flute's have upcut and downcut spirals all on one cutter, so down shear cutting on the top of your...20 replies | 35742 view(s) -
1 Week AgoYes sorry I was looking at it wrong.106 replies | 10549 view(s)
-
1 Week AgoI personally would have the switch fixed and have the target moving106 replies | 10549 view(s)
-
1 Week AgoDoes for me.6 replies | 528 view(s)
-
1 Week AgoNick you are correct but I am in discussion with Peter he tell me the ping times are too high 0.35. I am now looking into that the PC I am using...42 replies | 21258 view(s)
-
2 Weeks AgoClive S replied to a thread Advice on seller to purchase 2.2kw air cooled spindle from pretty please in Generic Chinese SpindlesRob. I am sorry to hear that. I wish you all the best.12 replies | 851 view(s)
-
2 Weeks AgoClive S replied to a thread Advice on seller to purchase 2.2kw air cooled spindle from pretty please in Generic Chinese SpindlesThat's fine but nearly £100 dearer than the one I posted to. I have just seen Rob's post I would take that12 replies | 851 view(s)
-
2 Weeks AgoClive S replied to a thread Advice on seller to purchase 2.2kw air cooled spindle from pretty please in Generic Chinese SpindlesYou have to be careful with the inverter see this:-...12 replies | 851 view(s)
-
2 Weeks AgoClive S replied to a thread Advice on seller to purchase 2.2kw air cooled spindle from pretty please in Generic Chinese SpindlesWelcome to the forum. The majority of people on here use the 2.2Kw W.C. spindle as they are much quieter and as they are water cooled if you need...12 replies | 851 view(s)
-
2 Weeks AgoFor the cat5 flex I use the white But not sure if there is any stardard15 replies | 1051 view(s)
-
2 Weeks AgoJon swift on this forum seems to collect a lot of bob schematics and might be able to help.11 replies | 924 view(s)
-
3 Weeks AgoYes I have a similar one BUT on the very small bootlace you have to crimp them twice ie. crimp it then just rotate the ferrule a tiny bit and crimp...15 replies | 1051 view(s)
-
3 Weeks AgoHave you considered soft limits?106 replies | 10549 view(s)
-
3 Weeks AgoIts not easy or practical to put a bottom limit switch on the Z axis as the tool lengths will all vary .106 replies | 10549 view(s)
Statistics
Total Posts
- Total Posts
- 2,976
- Posts Per Day
- 1.09
- Last Post
- Aluminium Profile Type Router - Initial questions 2 Days Ago
Total Thanks
- Total Thanks
- 58
General Information
- Last Activity
- 1 Hour Ago
- Current Activity
- Viewing Index MYCNCUK
- Join Date
- 17-10-2012
- Referrals
- 1
NordicCNC's build log