Milliamps and voltage help please
I have just bought a remote wireless camera from china and straight out of the box and setup is stunning.. I use a tiny first person view Sony camera and it gobsmacking quality. I took the camera down to the end of the garage and plugged it in via the wall sock power, according to destructions it uses 7 – 12 v and 400 mAh’s and I went back in the house upstairs at the far end to my bedroom and the quality again was stunning. So that’s about, in a straight line 80 feet through some pretty thick stone cottage walls and concrete block garage. But now I have a problem, which is why I need some advice. I ran the camera on a 9v NiMH 9 v 150 mA battery , went back to check and I didn’t expect to see anything but there was a pretty good quality picture, it did get a bit snowy now then I disappeared when I went near the receiver antenna. That’s fair enough I wasn’t expecting anything less from 150 mAh’s.
But I have a 7.2 v “1200” mAh battery, used for RC cars. So the question is can I use 1200 mAh’s on a 400 mAh piece of equipment or should I somehow reduce the output. Would it burn the camera or transmitter out or would it increase its range? The tank I’m putting it on works on 7.2 v’s and I have a 3400 mAh battery for it, what I would like to do is somehow build a power distribution board but don’t have a clue where to start.
Re: Milliamps and voltage help please
No expert here but to me the Ma rating will be what it draws when working at max so giving it higher doesn't mean it will draw more just that more is available if needed and will run for longer if the battery is the sole power source.? IE: 3400ma/400ma=8.5hrs use
Re: Milliamps and voltage help please
Fivetide; JAZZCNC is dead right here. It matters not a jot what the battery capacity is; it's all about being of the appropriate voltage and of sufficient capacity. Even if you could get and use a battery with 1000000 Ah capacity it'll be fine, so long as V is OK. Mind you the battery would be huge but last for ages!
Just remember I=V/R Ohm's law.
Re: Milliamps and voltage help please
Thanks chaps .. great answer :)
Re: Milliamps and voltage help please
Only downside to running the camera straight off the tanks battery is that the tank won't run for quite as long on a fully charged battery but the camera will be drawing next to nothing so won't make a great deal of difference.
Re: Milliamps and voltage help please
Hmmm
If it wants 7-12V then you can run a 9V battery a lot flatter than a 7.2V battery before it drops below 7V. The poor things do tend to fade before they reach their rated Ah.
I think it's looking for a 9 Volter.
Is it really drawing 400mA?
0.4A at 9V is 3.6W. Sees like a lot, does it run hot?
Re: Milliamps and voltage help please
Quote:
Originally Posted by
Robin Hewitt
Hmmm
If it wants 7-12V then you can run a 9V battery a lot flatter than a 7.2V battery before it drops below 7V. The poor things do tend to fade before they reach their rated Ah.
I think it's looking for a 9 Volter.
Is it really drawing 400mA?
0.4A at 9V is 3.6W. Sees like a lot, does it run hot?
Actually after looking again , its running at 260mA / 800mW, I think also the voltage may affect the range, as it quotes 800m to 1600m @ 12v/280mA's So I might be better finding a 12v battery if I want the better range. The more powerful ones quote 900mA's/2500mW's
Wireless AV
Re: Milliamps and voltage help please
I hope the tank battery is NiMh/NiCd not LiPo? If it's the latter then you need to be careful as they require a low voltage cutoff to stop them being damaged from over discharge. If it will tolerate up to 12.6V then a 11.1v (3 cells in series) lithium battery would be ideal since when fully discharged it would still be around 10V. Plenty on HobbyKing RC Plane, Car, Heli, Boat and MultiRotor Hobby Store ... if it's the first time you've seen that site you'll no doubt be up all night buying better batteries and all sorts for the tank!
Re: Milliamps and voltage help please
What sort of size is the tank it's going into? Sorry don't know much about radio controlled models except some seem to be quite big. Just thinking that a 12v battery from one of those motorized cycles would probably do a good job. Friend of mine lent me 2 to power a small trolley & I was surprised how powerful they were for such a compact size battery.
Re: Milliamps and voltage help please
Problem with a 12 Volt battery is you will get over voltage when fully charged. 9 Volts really is the best bet, unless you pop in a regulator.
Can you get a 9 Volt regulator or do they leap from 6 to 12? 12 would very quickly have the same problem, even if low drop out.