Mach 3 - Paralell port to ethernet adapter Windows 10 64Bit

Printable View

26-05-2019
myles.merry

Mach 3 - Paralell port to ethernet adapter Windows 10 64Bit

Hi Guys,

Is it a way that i can use a parallel port to Ethernet adaptor to connect my mach 3 board to my laptop with the Ethernet port.

Thanks,

Myles
26-05-2019
cropwell

Re: Mach 3 - Paralell port to ethernet adapter Windows 10 64Bit

https://www.amazon.co.uk/Ethernet-Co.../dp/B07KWBFPXW (found with google, in seconds)

BTW Mach3 with 64bit Win10 - does it work ? I have a feeling the answer is NO!
27-05-2019
Doddy

Re: Mach 3 - Paralell port to ethernet adapter Windows 10 64Bit

Quote:

Originally Posted by cropwell

https://www.amazon.co.uk/Ethernet-Co.../dp/B07KWBFPXW (found with google, in seconds)

BTW Mach3 with 64bit Win10 - does it work ? I have a feeling the answer is NO!

Just a slight cautionary note - as I have the 5-axis version of the above controller. Note, it's a 200kHz controller - the effect of this is the output pulses are active for 2.5us (I measured) and this can cause problems with cheaper stepper drivers (in my case, the opto-isolator response rate). The rather limited driver doesn't provide any mechanism to change the pulse width and doesn't honour the Mach3 settings. So, if you have one of these controllers, and you lose steps (in my case it was visually evident in operation) then look at the stepper driver response rate. DO NOT google for a pulse-extender, at least not on your company's IT system(!) Been there...

Didn't Mach3 get updated for Win10/64 bit? Either way, Win10 and auto-updates pee me off enough to stick with 7 for my controlling PC (running UCCNC/SX2.7, I still have XP on my Mach3/StarMill PC).
27-05-2019
magicniner

Re: Mach 3 - Paralell port to ethernet adapter Windows 10 64Bit

Quote:

Originally Posted by myles.merry

Hi Guys,

Is it a way that i can use a parallel port to Ethernet adaptor to connect my mach 3 board to my laptop with the Ethernet port.

Thanks,

Myles

Only if the driver gives Mach3 direct access to pin status control, it is not driven as a Parallel Port, doing so does not give motion control.
27-05-2019
m_c

Re: Mach 3 - Paralell port to ethernet adapter Windows 10 64Bit

Quote:

Originally Posted by Doddy

Just a slight cautionary note - as I have the 5-axis version of the above controller. Note, it's a 200kHz controller - the effect of this is the output pulses are active for 2.5us (I measured) and this can cause problems with cheaper stepper drivers (in my case, the opto-isolator response rate). The rather limited driver doesn't provide any mechanism to change the pulse width and doesn't honour the Mach3 settings. So, if you have one of these controllers, and you lose steps (in my case it was visually evident in operation) then look at the stepper driver response rate. DO NOT google for a pulse-extender, at least not on your company's IT system(!) Been there...

Didn't Mach3 get updated for Win10/64 bit? Either way, Win10 and auto-updates pee me off enough to stick with 7 for my controlling PC (running UCCNC/SX2.7, I still have XP on my Mach3/StarMill PC).

Most Leadshine drives require 5uS pulses. Not sure about the latest ones, but certainly the EM and standard ones did.

Mach3 will run on pretty much any modern version of windows, it's the parallel port driver that won't work on anything 64bit, or anything newer than Win7 (Win7 32bit is the last version the PP driver will work on). The reason is Microsoft switched to an encrypted kernel at that point, and as the PP driver relies on controlling the kernel, it wouldn't work without a lot of hacking. IIRC Art did manage to do some basic testing, but discovered the encryption regularly changes, so it just wasn't feasible.

Personally, if all you need is a single parallel port interface, I'd go for a UC100. It's not ethernet, but it's probably the simplest option with good support.