Re: Micro lathe Zero backlash* conversion
Quote:
Originally Posted by
m.marino
Actually, this video was made nearly 4 yrs ago and since then no other videos came out showing some metal turning but plastic.
If it was able to turn metal - builder would upload it for sure. Just makes me think is it not rigid enough???? not able to turn metal???
Will you Jonathan treat us with some action video??
Re: Micro lathe Zero backlash* conversion
Quote:
Originally Posted by
wiatroda
Actually, this video was made nearly 4 yrs ago and since then no other videos came out showing some metal turning but plastic.
If it was able to turn metal - builder would upload it for sure. Just makes me think is it not rigid enough???? not able to turn metal???
Will you Jonathan treat us with some action video??
Actually I think this lathe was purposely made to turn plastic.? I think the bloke is the same guy who makes Dumpster Anti backlash Delrin nuts but I could be wrong on that one thou I'm sure it was made just for plastic.!
Re: Micro lathe Zero backlash* conversion
Quote:
Originally Posted by
JAZZCNC
Actually I think this lathe was purposely made to turn plastic.? I think the bloke is the same guy who makes Dumpster Anti backlash Delrin nuts but I could be wrong on that one thou I'm sure it was made just for plastic.!
I bet you're right. never heard of those nuts:whistle:. But it would be nice to see some fancy shape metal turning anyway :)
4 Attachment(s)
Re: Micro lathe Zero backlash* conversion
This lathe has sat on the side doing nothing since I posted here, just not had time for it. A few days ago a 12Nm stepper motor arrived, which just so happens to fit the lathe mount, so how could I resist using it to power the spindle?
Attachment 6947
A few moments later:
Attachment 6948Attachment 6949
I had to take the covers off since now I don't have the right length belt which means the motor is in a funny place. I chose a 36:22 (motor:spindle) ratio since if we take the speed/torque curve from Zapp's site and convert it to more meaningful units, the peak power is around 600rpm so around 1000rpm spindle speed with that ratio.
Attachment 6950
I've only got the motor on 70V (DM860 drive), so that graph isn't ideal, but it seems to work well and runs the spindle up to 2000rpm. The motor was fine with drilling a 6mm hole in aluminium and general turning. I think I'll make a bigger pulley for the motor and try it anyway. The finish leaves a bit to be desired, but I think that's mainly the lathe itself being weak and having to have the material quite far from the chuck as currently the rear shaft on the motor interferes with the saddle. I don't think that will be a problem with the longer belt and if it is I can easily mill a little bit off the steel block I attached to the saddle to get clearance.
I configured LinuxCNC to run the stepper motor as the spindle by editing the .hal file - pretty simple. Next step is to get G33/G63 to work so I can do threading. I could just run it as an A-axis and program a ramp (e.g G1 Z-10 A10), but I'd prefer to do it properly...
Anyway, it seems this thread is useless without a video, so here goes:
http://www.youtube.com/watch?v=fHCu4...=youtube_gdata
Edit: Almost forgot to mention I solved the backlash problem on Z. Turns out it was just the belt being a bit loose, tightened it up and now the backlash is essentially zero - the 0.0001" indicator returns, as far as I can see, precisely to the same mark if approached from either direction.
I just need to make one piece for the X-axis so I can put the second nut in to get the same result. I wonder where the Belleville washers went. I think I've broken the magneto bearings whilst working out what was wrong, so I'll buy some better ones. He's got 708A and 708C so presumably that's the different contact angles - it would be good to know which is which so I can get the ones that tolerate higher axial forces!
Re: Micro lathe Zero backlash* conversion
Looks fantastic Great video mate