Thread: Not a good start
Hybrid View
-
03-07-2016 #1
Well my first go at a home cnc has got off to a bad start.
Bought a conversion kit for my little Proxxon mf70. Spent all day building it up only to blow the controller.
I got the kit from a company called gocnc.de and the instructions are not brilliant being just a load of pictures rather than anything written. To make matters worse the controller was slightly different to the one in the pic, hence i connected a wire to the wrong terminal and blew the board.
Has anyone had any experience of fitting one of these kits as im not €500 out of pocket with a ruined miller.
-
03-07-2016 #2
I'm going to guess you've bought some variation of this kit - http://abcnc.de/shop/en/cnc-router/3...cnc-custom-kit
In which case all you should need is a new Control Card Stepp 2500 from this page - http://abcnc.de/shop/en/cnc-acessories/cnc-controller/Avoiding the rubbish customer service from AluminiumWarehouse since July '13.
-
03-07-2016 #3
Yes that's the kit, but the controller was slightly different to the one shown on the site.
-
03-07-2016 #4
-
03-07-2016 #5
Post a picture of the board.
Those simple 3 axis boards are about £35 - £40 a pop and not 99 euro's but as said get them to replace it.John S -
-
03-07-2016 #6
Ok will do once I've got it off the machine.
-
03-07-2016 #7
That's what I've put in an email to them but they are the rudest bunch of people I've ever had to deal with so I don't think they are going to play ball unless I get my credit card involved.
-
03-07-2016 #8You think that's too expensive? You're not a Model Engineer are you? :D
-
The Following User Says Thank You to magicniner For This Useful Post:
-
16-07-2016 #9
Ok guys after finally getting my machine built and running ive now discovered that the software that comes with the usb control box with this kit will only run files that are HPGL format.
I only need to do cut outs etc in flat plate, so can anyone recommend a nice simple to use program that i can use to create the dxf and add the machinings to. I was hoping to use something like Vcarve but i dont think it saves as a HPGL file.
-
17-07-2016 #10
http://www.vectric.com/products/compare.html
FAQ at the bottom of the page, 3rd Q & AYou think that's too expensive? You're not a Model Engineer are you? :D
-
The Following User Says Thank You to magicniner For This Useful Post:
Thread Information
Users Browsing this Thread
There are currently 1 users browsing this thread. (0 members and 1 guests)
Similar Threads
-
NEW MEMBER: A new start for me.......
By Nthkentman in forum New Member IntroductionsReplies: 4Last Post: 23-08-2014, 10:50 AM -
Where to start?
By Inquisitor in forum Gantry/Router Machines & BuildingReplies: 7Last Post: 27-11-2012, 02:35 PM -
where to start?
By trounce in forum Gantry/Router Machines & BuildingReplies: 44Last Post: 03-10-2011, 02:03 PM -
is this 2.5d where do i start? help please if you can
By h4ppy-chris in forum General DiscussionReplies: 4Last Post: 29-03-2011, 12:21 PM -
NEW MEMBER: Were do I start?!
By tonygagey in forum New Member IntroductionsReplies: 4Last Post: 07-08-2010, 07:55 PM
Bookmarks