. .
  1. #1
    Due to other commitments (wife, children, vintage scooters etc) I have for sale the following items:-

    Additional info.
    http://www.iselcncmachines.co.uk/products/isel_prod/cat_cnc_mach.shtml



    • A number of single board PC’s, Arcom SBC104 with ¼ VGA displays and touch screens. I have data sheets and ARCOM utility disc software.
    Features
    · CPU: 80368SX 25MHz with PC/AT architecture.
    · Expansion: PC/104 expansion bus, 8/16-bit. Single master only.
    · BIOS: Chips and Technologies SCAT/SX BIOS (Basic Input-Output System) in 128KB flash EPROM
    · System memory: 2MB of Fast page DRAM.
    Optional 128KB of battery backed SRAM.
    · Silicon Disk:
    1MB of Intel SmartFlash, or 4MB of Intel StrataFlash.
    Includes Datalight Flash Filing system FlashFXTM.
    Includes Datalight ROM-DOSTM
    Support for M-SYSTEMS Disk-On-Chip silicon drives.
    · Integrated I/O:
    Battery backed Real Time Clock.
    AT keyboard interface via a 6-way mini DIN socket.
    IDE interface, supporting up to two IDE devices.
    FDD interface, supporting two Floppy Disk Drives up to 1.44MB.
    LPT parallel port, supporting SPP, and bi-directional EPP modes.
    Two 16C450 UART compatible RS232 serial ports (COM1 & COM2), up to 115200 Baud.
    Link selectable full-duplex RS-422 or half-duplex RS-485 available on COM2.
    Watchdog timer generating an NMI or optional RESET. Link selectable 3 second or 8 second time-out.


    Most software and technical details can be found in the internet. Some data sheets I have available.

    I thought that I would open them to sensible offers from users of this site first rather than put them on Ebay first then telling you they were on. Can send some pics (when I take them)

    Collection only (Cambridge) for the Isel & SM400.

    Contact Steve at [email protected]

  2. #2
    Has the isel got a model number and some idea of table size would be nice
    Peter

  3. #3
    Hi Peter
    The label has (as best as I can make out)
    Art-Nr 296101 9999
    Art Nr-Spindel - Mutter - Motor
    X 2111392063/2-13001
    Y 2111392063/2-13001
    It is large, the base is about 1m x 800mm, I will check the throw and get back to you with the X & Y travels.

    Steve

  4. #4
    I have measured the travel and it is 300mm x 320mm, will try to get some pictures ready if anyone is interested.

    Steve

  5. #5
    Sounds like the same machine I have.

    .
    John S -

  6. #6
    This little baby earns some serious coin, no way that's going.

    .
    John S -

  7. #7
    Hi,
    my name is josef, im new here can anybody help me, i have the same realy rare cnc controller like the beginner of this thread, its the modell sm400/gt4.
    the controller has a little error, the reference job will not work at the beginning, alsow axis who should not be in motion, crashes onto the endstoppers (have on the dip-switches into the controller turned on only the x-axsis, but the Z-axis alsow drives sometimes fully and without controll!
    should i fix this troubles , i need alsow a update from V9.0 to V17.?
    should anyone have a newer firmware as V17.3 and do not need the older eproms, i will buy from him,
    thanks for any tipps, and sorry for my bad english!

  8. #8
    Update:-
    The SM400 software is v16.45
    I have attached 3 pictures.

  9. #9
    SM400 software is v16.45
    Have added pictures (this time)
    I am open to offers if anyone is interested?
    Attached Files Attached Files

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. Mounting motor under table?
    By Rogue in forum Linear & Rotary Motion
    Replies: 51
    Last Post: 16-04-2012, 04:02 PM
  2. FOR SALE: ISEL Automation router GFM 4433
    By Nic in forum Items For Sale
    Replies: 3
    Last Post: 19-12-2011, 06:07 PM
  3. RFQ: Mounting Plate
    By ferus in forum Projects, Jobs & Requests
    Replies: 9
    Last Post: 26-10-2011, 02:56 AM
  4. Zapp Automation Discount Weekend !
    By Gary in forum Manufacturer News
    Replies: 6
    Last Post: 21-08-2011, 11:29 PM
  5. Mounting a chuck on a Rotary table
    By irving2008 in forum Machine Discussion
    Replies: 17
    Last Post: 02-09-2010, 07:23 PM

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •