. .
Page 7 of 8 FirstFirst ... 5678 LastLast
  1. #61
    m_c's Avatar
    Lives in East Lothian, United Kingdom. Last Activity: 3 Days Ago Forum Superstar, has done so much to help others, they deserve a medal. Has been a member for 9-10 years. Has a total post count of 2,908. Received thanks 360 times, giving thanks to others 8 times.
    Quote Originally Posted by Agathon View Post
    Do you know what the ratio was on the Triac servos?
    I've only got the parts list for the stepper version, and it uses 12:30. Chaz has a servo version, but I don't think there would be much room to go for a higher ratio.
    Avoiding the rubbish customer service from AluminiumWarehouse since July '13.

  2. #62
    What size timing pulleys would you suggest for 200 or 400 watt servos? I was thinking that 5M 9mm wide belt should be about right. Centres should be around 100mm.
    Last edited by Agathon; 23-07-2017 at 11:35 PM.

  3. #63
    I'd say 15mm belt width minimum.
    Gerry
    ______________________________________________
    UCCNC 2022 Screenset

    Mach3 2010 Screenset

    JointCAM - CAM for Woodworking Joints

  4. #64
    m_c's Avatar
    Lives in East Lothian, United Kingdom. Last Activity: 3 Days Ago Forum Superstar, has done so much to help others, they deserve a medal. Has been a member for 9-10 years. Has a total post count of 2,908. Received thanks 360 times, giving thanks to others 8 times.
    If you download the Gates DF software, it will generate suitable drive options.
    Avoiding the rubbish customer service from AluminiumWarehouse since July '13.

  5. #65
    Just in case you helpful fellows haven't seen my new thread on trying to connect up the drivers to the BOB - here it is: http://www.mycncuk.com/threads/11159...ut-board-Mach3

  6. #66
    Hi guys, I'm going to build a machine to drill and tapping one part, I'm thinking use a servo for tapping and a regular spindle for drilling. Using a regular servo I can do rigid M3 tapping on 2mm aluminium sheet? Have anyone experience with something similar? Tks

    Enviado de meu Redmi Note 4 usando Tapatalk

  7. #67
    Quote Originally Posted by lp_felix View Post
    Hi guys, I'm going to build a machine to drill and tapping one part, I'm thinking use a servo for tapping and a regular spindle for drilling. Using a regular servo I can do rigid M3 tapping on 2mm aluminium sheet? Have anyone experience with something similar? Tks

    Enviado de meu Redmi Note 4 usando Tapatalk
    To do rigid tapping you will need a quadrature encoder on the servo and some thing like Linuxcnc to control it.

    Here is a link in Portugal where you can buy the Mesa cards 6i25 with 7i77 bob will do it.

    Are you think of having the spindle and servo on the same gantry?
    ..Clive
    The more you know, The better you know, How little you know

  8. #68
    You can also do rigid tapping with UCCNC, and with Mach3/4 with the right motion controller.
    Gerry
    ______________________________________________
    UCCNC 2022 Screenset

    Mach3 2010 Screenset

    JointCAM - CAM for Woodworking Joints

  9. #69
    Quote Originally Posted by Clive S View Post
    To do rigid tapping you will need a quadrature encoder on the servo and some thing like Linuxcnc to control it.

    Here is a link in Portugal where you can buy the Mesa cards 6i25 with 7i77 bob will do it.

    Are you think of having the spindle and servo on the same gantry?
    Yes, spindle and servo on same gantry.. Ok, I have a lot of questions but i will study quadrature encoder and servo first, and do stupid questions later.. Thank you for the help.

    Enviado de meu Redmi Note 4 usando Tapatalk

  10. #70
    Quote Originally Posted by Ger21 View Post
    You can also do rigid tapping with UCCNC, and with Mach3/4 with the right motion controller.
    Hi Ger21, in fact I planing use uccnc. I have a spare Uc300 5lpt (from other unfinished project) I will read the manual.
    Thanks for the tip.

    Enviado de meu Redmi Note 4 usando Tapatalk

Page 7 of 8 FirstFirst ... 5678 LastLast

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. CS-LAB AC-servos + SIMdrive
    By blim in forum Stepper & Servo Motors
    Replies: 0
    Last Post: 20-02-2017, 12:52 PM
  2. Novice- need buying advice
    By davespg996 in forum New Member Introductions
    Replies: 1
    Last Post: 09-02-2017, 11:12 AM
  3. Advice on Buying a Benchtop CNC
    By Richb in forum Marketplace Discussion
    Replies: 12
    Last Post: 27-06-2016, 06:43 PM
  4. Mitsubushi Servos
    By Chaz in forum General Electronics
    Replies: 0
    Last Post: 24-04-2016, 08:08 PM
  5. Machine Buying advice
    By jrob3rts in forum Marketplace Discussion
    Replies: 0
    Last Post: 17-09-2010, 04:59 PM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •