. .
  1. #1
    Just ordered a couple of these for a project and thought others may find them useful

    Link: https://www.ebay.co.uk/itm/132411077076

    Video of one use:

    .Me

  2. The Following User Says Thank You to Lee Roberts For This Useful Post:


  3. #2
    Just had an email through about a 24v version of this, may be better for those running a 24v setup.

    Link: https://www.ebay.co.uk/itm/282258800401
    .Me

  4. #3
    Well that is very confusing! Is it a variable frequency generator to drive a stepper motor (it says that a separate drive is needed) or a PWM controller? There's a meaty device with a heatsink but maybe that's just a regulator as it says that you can supply from 160 V.

  5. #4
    The guy in the video likes living dangerously - drilling holes in an ali block holding the rough cut edges in his fingers! And I don't know if it's the effect of the camera, the playback or what but at low speed the stepper seems to be very jerky.
    Last edited by JohnHaine; 15-07-2018 at 09:57 AM.

  6. #5
    Well he's still got ten fingers and not too many scars, so he must be doing something right !
    Cheers

    Andrew
    Last edited by the great waldo; 15-07-2018 at 12:24 PM.

  7. #6
    Quote Originally Posted by JohnHaine View Post
    Well that is very confusing! Is it a variable frequency generator to drive a stepper motor (it says that a separate drive is needed) or a PWM controller? There's a meaty device with a heatsink but maybe that's just a regulator as it says that you can supply from 160 V.
    Either, it depends on the jumper setting.

  8. #7
    Clive S's Avatar
    Lives in Marple Stockport, United Kingdom. Last Activity: 12 Hours Ago Forum Superstar, has done so much to help others, they deserve a medal. Has been a member for 9-10 years. Has a total post count of 3,333. Received thanks 618 times, giving thanks to others 77 times. Made a monetary donation to the upkeep of the community. Is a beta tester for Machinists Network features.
    Quote Originally Posted by the great waldo View Post
    Well he's still got ten fingers and not too many scars, so he must be doing something right !
    Cheers

    Andrew
    And no thumbs
    ..Clive
    The more you know, The better you know, How little you know

  9. #8
    Quote Originally Posted by the great waldo View Post
    Well he's still got ten fingers and not too many scars, so he must be doing something right !
    Cheers

    Andrew
    Well, so far it hasn't gone wrong!

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. Replies: 3
    Last Post: 02-09-2021, 11:08 PM
  2. pulse generator for M542 to use on a optimum BF46 Vario
    By gnalbant in forum Optimum Milling Machines
    Replies: 2
    Last Post: 03-07-2016, 11:50 AM
  3. Stepper motor Pulse Signal Generator module
    By Tom J in forum Motor Drivers & Controllers
    Replies: 8
    Last Post: 12-01-2016, 11:47 AM
  4. Stepper motor as a generator??
    By wiatroda in forum General Discussion
    Replies: 10
    Last Post: 08-08-2011, 10:17 PM
  5. Motor controller next to break out board?
    By m_c in forum General Electronics
    Replies: 2
    Last Post: 17-11-2010, 01:56 PM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •