1. #1
    I am doing a conversion on a Novamill and require a couple of pins for the connector socket.

    The plug has a name contart on it. there is a ref. on the docs for the pin "male insert B1 357 H
    Click image for larger version. 

Name:	IMG_20181108_114842.jpg 
Views:	16 
Size:	252.7 KB 
ID:	25039
    Click image for larger version. 

Name:	IMG_20181107_144329.jpg 
Views:	16 
Size:	376.1 KB 
ID:	25040
    Click image for larger version. 

Name:	IMG_20181107_142719.jpg 
Views:	17 
Size:	329.3 KB 
ID:	25041

    Any clue as to where I could get them and do they need a tool to insert them.
    Last edited by Clive S; 6 Days Ago at 01:21 PM.
    ..Clive
    The more you know, The better you know, How little you know

  2. #2
    m_c's Avatar
    Lives in East Lothian, United Kingdom. Last Activity: 15 Hours Ago Forum Superstar, has done so much to help others, they deserve a medal. Has been a member for 9-10 years. Has a total post count of 2,163. Received thanks 242 times, giving thanks to others 5 times.
    RS do the bits, but I can't find the details right now.

    Don't know why that has got Contart on it, but it's a Harting connector system.

    I can tell you the release tool is RS part no 114-7728, as I had to buy one to swap a few things around on my Triac. I thought I had also ordered the terminals, but a search of my email isn't showing any relevant orders other than for the release tool.
    Avoiding the rubbish customer service from AluminiumWarehouse since July '13.

  3. The Following User Says Thank You to m_c For This Useful Post:


  4. #3
    Quote Originally Posted by m_c View Post
    RS do the bits, but I can't find the details right now.

    Don't know why that has got Contart on it, but it's a Harting connector system.

    I can tell you the release tool is RS part no 114-7728, as I had to buy one to swap a few things around on my Triac. I thought I had also ordered the terminals, but a search of my email isn't showing any relevant orders other than for the release tool.
    That's very helpful, thanks.

    Would you say it was this one https://uk.rs-online.com/web/p/heavy...ctors/1444239/

    I have found this pin https://uk.rs-online.com/web/p/heavy...ories/0408319/ 3.74 pk 10 + vat

    or this https://uk.rs-online.com/web/p/heavy...ories/1567267/ 34 pk 50 +vat bit steep I only need two
    Last edited by Clive S; 5 Days Ago at 03:16 PM.
    ..Clive
    The more you know, The better you know, How little you know

  5. #4
    m_c's Avatar
    Lives in East Lothian, United Kingdom. Last Activity: 15 Hours Ago Forum Superstar, has done so much to help others, they deserve a medal. Has been a member for 9-10 years. Has a total post count of 2,163. Received thanks 242 times, giving thanks to others 5 times.
    The relevant Harting catalogue for that connector should be attached, so probably best to double check measurements/contacts, as the Triac uses more terminals. I'm pretty sure they still use the same series of connector, just the Triac has two more rectangular modules in the housing.

    I thought I had ordered contacts, but I can't find any or any evidence of ordering them. I suspect I may of just reused contacts, as they require a circular crimp tool which I definitely don't have. If you crimp them with normal crimping pliers they might not fit the housing, as they are quite a tight fit.

    Click image for larger version. 

Name:	Han_16_Han_HMC_en (1).pdf 
Views:	21 
Size:	2.00 MB 
ID:	25044
    Avoiding the rubbish customer service from AluminiumWarehouse since July '13.

  6. #5
    Thanks for the info.

    I ordered these https://uk.rs-online.com/web/p/heavy...ories/0408319/ 4pm last night and they were here by 12 noon.

    I soldered the cables into the pins and slid them in from the back. simples. So now I have enough cables to change the feed & speed pots to alps encoders.
    Last edited by Clive S; 4 Days Ago at 02:39 PM.
    ..Clive
    The more you know, The better you know, How little you know

Similar Threads

  1. Which circular connector for spindle
    By ROBCNCAU in forum Spindles & Drive Motors
    Replies: 7
    Last Post: 19-06-2016, 09:20 AM
  2. Connector for THC ?
    By Davek0974 in forum Plasma Table Machines
    Replies: 0
    Last Post: 13-06-2014, 02:51 PM
  3. Spindle water hose connector
    By cncJim in forum Marketplace Discussion
    Replies: 6
    Last Post: 20-02-2014, 11:22 AM
  4. Cable + Connector issues
    By tom3d in forum General Electronics
    Replies: 0
    Last Post: 09-01-2012, 07:56 PM
  5. limit switch connector options?
    By routercnc in forum General Electronics
    Replies: 5
    Last Post: 04-09-2010, 02:11 PM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •