1. #1
    Hello All,
    I thought I'd share my progress with my sound dampening enclosure I've been building for my CNC router.
    When I started building my CNC, I knew I'd have to have some sort of enclosure, and with the neighbours that I have it would have to be pretty effective at cutting down the noise.

    Enclosure is made of an MDF outer shell, then a 10mm gap, then the inside "panels", which are HEAVY.

    Each panel is made up of the following layers. 12.5mm plasterboard, CLS timber frame filled with 50mm Rockwool sound insulation, 10mm carpet, 18mm MDF, 10mm carpet again (around the rim only this time, leaving a 10mm gap in the middle).

    The completed panels are extremely heavy. After calculating based on the weight of a sheet of mdf and plasterboard, I'd have to say close to 45-50kg each. Thickness of each panel comes to around 110mm.

    The only screws used on the panels was to make the CLS frame. All layers are glued together using either contact adhesive (for the carpet, mdf layers) or gripfill (for the plasterboard layers). I wanted to minimize the amount of vibration transference through screws and bolts by omitting them altogether.

    Here are a few pics. I still have the front panel/Door to make tomorrow, and I'm still unsure how I will hinge it. Also to do are ports for cables and baffles for fans/airflow.




















  2. #2
    Thanks for sharing, that should do a pretty good job.

    It would be interesting if you could let us know how much noise it cuts out when you are up and running.

    Cheers

  3. Looks good. Box in box is a classic solution and with minimum structural connection between them should work well. Note that the surrounding inner box will amplify the sound inside which makes the outer box work harder. The carpet will help with absorption but only at fairly high frequencies. If you can line the ceiling with something thicker and fluffier it will help.

    Services in and out are best done with long trunking lined with absorption, so donít just go straight through each panel but start at the top (say) of the inner and bend 90 deg down to run down the void, with a rubber coupling in the middle, then bend 90 and go out of the outer panels. So the upper trunking is mounted to the inner panel and the lower trunking is mounted to the outer panel. You can get rectangular trunking which might fit depending on the gap size.

    Good work
    Building a CNC machine to make a better one since 2010 . . .
    MK1 (1st photo), MK2, MK3, MK4

  4. #4
    I think the idea of sound proofing is good, but I also think that the table is not going to be strong and rigid enough for a CNC and that the rubber wheels will make the whole machine too shaky. My CNC is made in a similar way but out of 45x90 aluminium extrusions and originally I also had similar wheels, but after some use I realized that the shake is just too violent when the CNC was in use and that it also affected maximum speed and accuracy, so I changed the solution. The table is now lowered onto the floor, and the wheels are only used when I want to move it around, which is not happening that often. Also, the noise level actually dropped after the change, even though the aluminium extrusion feet is not touching the floor, resting directly on some wooden blocks between the floor and the machine feet. My advice it that you think about this before it is too late, so you don't have to make too many changes later.

Similar Threads

  1. BUILD LOG: Finished builds picture menu
    By routercnc in forum DIY Router Build Logs
    Replies: 8
    Last Post: 24-05-2018, 10:21 PM
  2. BUILD LOG: Finished. DIY CNC
    By Husky1 in forum DIY Router Build Logs
    Replies: 9
    Last Post: 07-05-2018, 01:12 PM
  3. CNC router enclosure
    By Leadhead in forum Workshop & Equipment
    Replies: 2
    Last Post: 03-05-2018, 11:00 PM
  4. router sound proofing
    By universally in forum General Discussion
    Replies: 4
    Last Post: 02-10-2015, 05:30 PM
  5. Drill / Tap Guide Jig - Finished!
    By Wal in forum Metalwork Project Showcase
    Replies: 10
    Last Post: 04-12-2014, 09:59 PM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •