. .
  1. #1
    Hi, can anyone help me out with the setting for the VFD YL620-A2.2KW 220V and 2.2KW water cooled spindle?

    I bought my spindle and VFD 5 years ago and never used them, however I've now fitted them on a CNC router and the VFD failed so trying to add the VFD YL620-A2.2KW 220V (Amazon) but don't want to damage the spindle.

    I have done a factory reset P0.13 =10

    Is there some standard starting setting?

    If I'm wasting my time with the VFD please tell me, as I'll send back but obviously want to get it going.

    many thanks

    Allan

  2. #2
    The one you have will work. But I am not familiar with this it.

    The one that I would use (if you could send it back) would be the tried and tested :-

    https://www.ebay.co.uk/itm/Speed-Con...sAAOSw97RfAuIN

    some of the important settings is the motor number of motor poles I think it is 2 if you have the Chinese 2.2kw spindle

    and the input voltage & current. Also the max frequency 400Hz so the the spindle will run at 24K
    ..Clive
    The more you know, The better you know, How little you know

  3. #3
    Have a look here... https://en.industryarena.com/forum/h...117782-33.html, reply 655.

    Don't know this VFD at all, so can't advise further other than Google is your friend.

    Clive's advice above about getting motor poles/voltage is perfectly sound. You'll hate me for saying this but I wouldn't have recommended resetting any parameter without first going through the lot and recording the delivered pre-sets.

  4. #4
    I've just found this sheet that is to the VFD I have, I've set as listed but not sure about the middle & low frequency & voltage settings, they don't look right to me, I'll attach a copy

    thanks

    Allan
    Attached Files Attached Files

  5. #5
    I've seen a post with these setting?

    P00.00 – 50Hz
    P00.04 VF highest output frequency – 400Hz
    P00.05 VF maximum voltage output frequency - 400Hz
    P00.06 VF highest output voltage – 100%
    P00.07 VF middle frequency – 200Hz
    P00.08 VF middle voltage – 50%
    P00.09 VF minimum frequency - 120Hz
    P00.10 VF minimum voltage – 30%

    but the manual say's

    P00.00 – 50Hz
    P00.04 VF highest output frequency – 400Hz
    P00.05 VF maximum voltage output frequency - 400Hz
    P00.06 VF highest output voltage – 100%
    P00.07 VF middle frequency – 40Hz
    P00.08 VF middle voltage – 10%
    P00.09 VF minimum frequency - 4.0Hz
    P00.10 VF minimum voltage – 1%

    confusing!

  6. #6
    I wouldn't worry about the differences as none will stop it from working or damage it.
    -use common sense, if you lack it, there is no software to help that.

    Email: [email protected]

    Web site: www.jazzcnc.co.uk

  7. #7
    Hi JAZZCNC

    do you think the top settings seem more reasonable
    ?

    Allan

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. Replies: 17
    Last Post: 11-09-2019, 11:19 PM
  2. Water cooled vs Air cooled spindle for wood
    By Bucks in forum Machine Discussion
    Replies: 5
    Last Post: 06-02-2017, 01:58 PM
  3. Water cooled / air cooled 2.2kw spindle
    By suesi34e in forum Generic Chinese Spindles
    Replies: 15
    Last Post: 25-02-2015, 04:57 PM
  4. Do you need to water cool erhm a water cooled spindle?!!
    By HankMcSpank in forum Generic Chinese Spindles
    Replies: 18
    Last Post: 02-10-2013, 09:59 PM
  5. Replies: 17
    Last Post: 18-09-2013, 06:32 AM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •