. .
  1. #1
    Redz's Avatar
    Lives in Plymouth, United Kingdom. Last Activity: 24-01-2021 Has been a member for 0-1 years. Has a total post count of 3.
    Any recommendations for cnc lathes that will be good at turning tungsten darts?

  2. #2
    Tungsten isn't a very easy material to turn I believe and will require a good lathe with correct tooling/inserts. I think most tungsten is ground rather than turned.? But I'm not a lathe guy so could be wrong.!

    But if you are wanting something more than a hobby machine I do have the perfect machine that will do this standing on its head.
    It's a BIG Tarex Burger twin ATC turret lathe with hydraulic Collet chuck, Fanuc 11T controller, and Fanuc AC Red top servos, it's a serious bit of kit that is the size of a small car but it's your for £2k.
    -use common sense, if you lack it, there is no software to help that.

  3. #3
    Quote Originally Posted by Redz View Post
    Any recommendations for cnc lathes that will be good at turning tungsten darts?
    Is tungsten not sintered in a mould and ground? There are some examples of turning on youtube using cbn tips.
    Last edited by Colin Barron; 22-01-2021 at 12:04 AM.

  4. #4
    Are they "Tungsten" or "Tungsten carbide"

  5. #5
    Quote Originally Posted by johnsattuk View Post
    Are they "Tungsten" or "Tungsten carbide"
    https://www.youtube.com/results?sear...ten+on+a+lathe
    Normally tungsten carbide is fitted to wear surfaces by brazing and then ground flat or square.

  6. #6
    Have some past experience of "Tungsten carbide" dart manufacture, still have some somewhere.
    They were pressed blanks, shaped drilled etc and then sintered

    Tungsten carbide - high density - smaller barell

  7. #7
    Would copper tungsten be a better material to use? The high tungsten variants have similar density to tungsten carbide (WC !) and I'm told it's a lot more machineable.

  8. #8
    High quality Tungsten darts have a body in metal alloy with up to 97.5% tungsten, not Tungsten Carbide in a sintered substrate, tungsten metal has a significantly higher density than tungsten carbide in a sintered substrate.
    You think that's too expensive? You're not a Model Engineer are you? :D

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. Lathe recommendations for Tungsten.
    By Redz in forum Machine Discussion
    Replies: 0
    Last Post: 20-01-2021, 06:10 PM
  2. Lathe/programme recommendations
    By Redz in forum Lathes, Lathe Rebuilding & Conversions
    Replies: 0
    Last Post: 19-01-2021, 09:57 PM
  3. Lathe DRO recommendations
    By Filco in forum Lathes, Lathe Rebuilding & Conversions
    Replies: 20
    Last Post: 05-10-2020, 05:56 PM
  4. NEW MEMBER: Hello all :) Old dog to learn new tricks, cnc lathe turning is main interest
    By Rob in forum New Member Introductions
    Replies: 0
    Last Post: 12-01-2016, 09:22 PM
  5. CNC Lathe recommendations?
    By UltraMagnus in forum Lathes, Lathe Rebuilding & Conversions
    Replies: 0
    Last Post: 07-09-2011, 08:51 PM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •