. .
  1. #1
    hi all
    i am mike from essex
    since being retired i have been building a workshop which has been sucessfull
    finally i have manged to get a lathe, needs a bit TLC but it will be good when working
    i will be building antenna, radio equipment and other bits as well
    happy to answer any questions
    regards mike

  2. The Following User Says Thank You to thenextdoctor For This Useful Post:


  3. Hi Mike,

    I am also in Essex, been mucking about with machine tools for a long time.

    I guess that you are involved in Amateur radio in some way. I played with that 20 us years ago, strung a long aerial across my garden. Did a little listening but not much more.

    Ran some CNC lathes back in the 90s, built a router few years ago. Now just playing in the shed making small 2 stroke diesel parts.

    Do you have any specific reasons for joining here? It's all very friendly here 99 times out of a 100 :)


    Enjoy the forum
    Regards Simon

    Sent from my COL-L29 using Tapatalk

  4. #3
    Simon
    Many thanks for your message. Yes I am well into ham radio, my story regarding lathes. I use to use one at school and said i gotta get one of these. Now retired and needing to get and make bits. Finally I found a lathe that I think will be OK for me and the price was right too. Its a Holbrook Edgar and seems to be pretty good. I do have 1 issue (at the moment) with it. It does not have a toll post. I was hoping someone here can advice me which post I shoud get, most of the info I have pictures show the lather without a tool post.

    What you are doing sounds pretty good, as long as you are enjoing you making diesel parts thats good. Its also good to meet someone from essex, i am in basildon.
    all the besst
    regards
    Mike

  5. #4
    AndyGuid's Avatar
    Lives in Pakenham, Melbourne, Australia. Last Activity: 41 Minutes Ago Has been a member for 8-9 years. Has a total post count of 195. Received thanks 31 times, giving thanks to others 285 times.
    Do you have one of the lathes as shown in these pictures Mike? http://www.lathes.co.uk/edgar/index.html

  6. #5
    Andy
    Yes the top picture is the one I have, but the treedle has been removed and its now powered by a moter 240V
    regards
    mike

  7. #6
    OMG what a super little lathe, I keep an ML10 for when I get nostalgic but it's not a patch on that

    Robin

  8. #7
    Robin
    Its solid and has not had much use, just needs a clean reoil, its in bits in my garage just awaiting to complete the woodwork in the shed, than it will be set up for use.Its also super heavy as well but no tool post, hoping someone here has one with a tool post. Hopefully a multi change post. So that I can get the right item for the edgar
    regards
    mike

  9. #8
    phill05's Avatar
    Lives in Derbyshire  UK, United Kingdom. Last Activity: 21 Hours Ago Has been a member for 9-10 years. Has a total post count of 279. Received thanks 25 times, giving thanks to others 12 times.
    Mike have a look here: https://groups.io/g/holbrook/topics all about Holbrooks you can join and get all the info you need, I have a small CB8 best lathes you can get

    Phill

  10. #9
    Phil
    Many thanks for the info, I am trying to join the group
    see you on the group phil
    regards
    mike

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. NEW MEMBER: New Member from Across the Pond-and an Introduction to My CNC Lathe Project
    By acollins in forum New Member Introductions
    Replies: 2
    Last Post: 13-05-2012, 09:14 PM
  2. CNC style lathe home brew Lathe for drilling and cutting.
    By Bodge in forum Lathes, Lathe Rebuilding & Conversions
    Replies: 9
    Last Post: 18-04-2012, 09:45 AM
  3. NEW MEMBER: New member what to buy ?? mill and lathe
    By funni in forum New Member Introductions
    Replies: 0
    Last Post: 25-11-2009, 01:33 PM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •