. .
Page 2 of 2 FirstFirst 12
  1. #11
    Quote Originally Posted by XYZ_Spec View Post
    It's already done for you inside the bags.
    Pre-mixed, just have to add water
    Lucky you. Pms share the name on the mix, i wanna see the technical data sheet and see what i can find close to it locally

  2. #12
    Quote Originally Posted by masinecc View Post
    Lucky you. Pms share the name on the mix, i wanna see the technical data sheet and see what i can find close to it locally
    Here it is the manufacturers site page for this product I've used.
    It seems to be only available in Portuguese language.
    This is the best I can do for you.

    https://www.cimpor.com/-/betao-seco-be-30

  3. #13
    Quote Originally Posted by masinecc View Post
    Lucky you. Pms share the name on the mix, i wanna see the technical data sheet and see what i can find close to it locally
    Same...

    Quote Originally Posted by XYZ_Spec View Post
    Here it is the manufacturers site page for this product I've used.
    It seems to be only available in Portuguese language.
    This is the best I can do for you.

    https://www.cimpor.com/-/betao-seco-be-30
    Thanks for sharing...

    What about this probe, how you finding it, accuracy etc?

    https://youtube.com/shortsNtOfxCaf4lU

    P.S Is it still v6: 3D Touch Probe Edge Finder ???
    Last edited by Lee Roberts; 29-09-2022 at 10:46 PM. Reason: Probe link
    .Me

  4. #14
    Quote Originally Posted by Lee Roberts View Post
    What about this probe, how you finding it, accuracy etc?

    https://youtube.com/shortsNtOfxCaf4lU

    P.S Is it still v6: 3D Touch Probe Edge Finder ???
    Yes Lee, V6.
    I like it a lot, and it's not crazy expensive.
    I want to install it permanently onto the spindle mount, this will allow me to set zero without having to do a tool change.

  5. The Following User Says Thank You to XYZ_Spec For This Useful Post:


  6. #15
    Hi guys,

    One year after designing and 3D printing a prototype that failed because it wasn't water proof, finally machined the housing from aluminum.
    I'm really happy with how it came out.
    It was a really cool project.

    Hope you enjoy it too.


  7. #16
    Nice, what finish did you use paint or anodised?
    .Me

  8. #17
    Quote Originally Posted by Lee Roberts View Post
    Nice, what finish did you use paint or anodised?
    Spray paint.
    One day will anodize all the aluminum parts.

  9. #18
    Ok I thought so, keep an eye on the internal paint, the coolant *could* react with the paint and make it dissolve/flake off and block your spindle internal tubes, it should be ok I think but something to check later...
    .Me

  10. #19
    I'll keep an eye on it. I was hesitating to paint the interior bore, but I thought if i didn't try I would not know

    Thanks for your tip Lee

Page 2 of 2 FirstFirst 12

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. Damping Test of Concrete & Steel Tube
    By Tenson in forum General Discussion
    Replies: 11
    Last Post: 16-05-2022, 01:26 PM
  2. Adding a Laser to my steel and concrete machine
    By Bongo in forum Gantry/Router Machines & Building
    Replies: 2
    Last Post: 16-05-2022, 12:28 PM
  3. Machining lighweight (AAC) concrete blocks.....
    By Voicecoil in forum General Discussion
    Replies: 4
    Last Post: 03-07-2020, 08:32 PM
  4. FOR SALE: Snowcrete Concrete - 14 x 25 KG Bags
    By Chaz in forum Items For Sale
    Replies: 1
    Last Post: 13-04-2019, 04:32 PM
  5. concrete base
    By reefy86 in forum General Discussion
    Replies: 6
    Last Post: 04-12-2017, 09:55 AM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •