. .
  1. #1
    hello please
    3 positec 5 phase mini motors and a pac controller
    3x little 5 phase motors - they dont like the mach i think as they are a 10 wire motor
    about 45mm long with a 60mm bolt doofer - so not like nema 23 which is 57mm
    erm
    the controller is a three axis affair with cards that kind of plug in
    again 5 phase
    ran from a 24v psu
    thanks

    erm has a breakout board of the rs232 variety
    a power card

    50 quid the lot

    i will have another one next weekend too
    plus me thinks a 2 axis foam cutting machine, smallish

    very nice
    located in the fulham = i.e. collection only
    postage is £150

    i am cutting the cables from the motors and using the rs232 ends to my new drives and motors
    i just bought tint nema 23's 8 wire and some little drivers - why I don't know - or I know I can get it to work.

    this maybe really easy for you
    came from a high end mini mill

    ta
    Last edited by nobby; 31-01-2023 at 07:37 PM.

  2. #2
    Pics of the three phase motors/controller ?

  3. #3
    Click image for larger version. 

Name:	IMG_20230131_181206.jpg 
Views:	52 
Size:	124.5 KB 
ID:	31700
    Click image for larger version. 

Name:	IMG_20230131_181143.jpg 
Views:	52 
Size:	248.3 KB 
ID:	31701
    Click image for larger version. 

Name:	IMG_20230131_180920.jpg 
Views:	45 
Size:	191.3 KB 
ID:	31702
    Click image for larger version. 

Name:	IMG_20230131_181025.jpg 
Views:	46 
Size:	149.5 KB 
ID:	31704
    Click image for larger version. 

Name:	IMG_20230131_181020.jpg 
Views:	45 
Size:	135.8 KB 
ID:	31703

    3 motors no cables - i am using them on my new motors and drivers
    i could leave it all ready to run IF you vcan work out the inputs into the rs232 port on the controller and sell you the unmessed with cabling

    the rs232 in is only 11 pins so you can work out the pulses to that and the torch controll you are golden really
    I can - or do not wish to bother = i am cutting off the cables and using the rs232 ends to my new drivers - or I could just get new wire and charge you more money

    then you have a sweet little 5 phase machine 500 pulses per rev

    i bet you could simply plug it into a rs232 port on a computer and run mach through it.
    Last edited by nobby; 31-01-2023 at 07:38 PM.

  4. #4
    i have just picked up the other machine
    its 4 axis
    similar looking controller and drive set up
    with older but the same motors

    circa i think 1998

    will do a deal if you buy the lot

    thanks

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. AT1 Single Phase to Three Phase Penske Spindle Woes....
    By Cozza in forum Spindles & Drive Motors
    Replies: 6
    Last Post: 14-07-2021, 10:01 PM
  2. Replies: 0
    Last Post: 10-05-2021, 05:32 PM
  3. VFD 220v single phase to 380v three phase.
    By Richard in forum General Discussion
    Replies: 28
    Last Post: 14-12-2020, 11:19 PM
  4. Positioning three phase induction motors.
    By Agathon in forum Motor Drivers & Controllers
    Replies: 2
    Last Post: 23-04-2020, 01:02 PM
  5. Panasonic 3 phase driver running on 1 phase?
    By gavztheouch in forum Motor Drivers & Controllers
    Replies: 2
    Last Post: 10-05-2012, 11:21 PM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •