. .
Page 1 of 2 12 LastLast
  1. #1
    When I worked with CNC mills many many years ago, to set the datum on X and Y we used a wobbler, basically a 0.2 dia ball mounted tip that deflected when very close to datum edge.

    What is used now to set the datum on X & Y axes.

  2. same thing - a wiggler or an edge finder, unless you have some clever laser-y video-y thing...

  3. #3
    Quote Originally Posted by irving2008 View Post
    same thing - a wiggler or an edge finder, unless you have some clever laser-y video-y thing...
    Ah, the old school techniques, tested and proven.

    Where might I source one of these wigglers or wobblers now.

  4. eBay... or Chronos have a good range here - I have the 4mm EFZ4 only £7.95 inc p&p

  5. #5
    Quote Originally Posted by irving2008 View Post
    eBay... or Chronos have a good range here - I have the 4mm EFZ4 only £7.95 inc p&p

    £7.95 .... is that a typo perhaps, only prices I found were £79+

    at those sort of prices I would be looking at modding a pocket laser.

    Just looked at the edge finders you mention, would you mind explaining how they work.
    Last edited by compfranon; 28-03-2010 at 02:09 AM.

  6. you put them in the spindle, set it spinning, then jog to the X-axis datum edge until the edge finder 'splits', raise the Z, jog in a further 2mm (for a 4mm one) and zero the DRO or set the axis zero as appropriate. then repeat for the Y-axis... see video


  7. The Following 2 Users Say Thank You to irving2008 For This Useful Post:


  8. #7
    Thanks Irving, they operate pretty much the same as the wobblers I remember. Might look out for the led version on fleabay, looks useful if datuming a rear edge.

  9. #8
    Forget about the light up ones, they are just a gimmick, designed to attract moths that think they will do a better job. Just try using them on a non conductive material, you will soon realise why. I actually gave one away a couple of days ago. As useful as a bowler hat with sleeves.

    The ones from Arc Euro do a great job.

    http://www.arceurotrade.co.uk/Catalo...t/Edge-Finders

    Bogs

  10. #9
    Quote Originally Posted by bogstandard View Post
    Forget about the light up ones, they are just a gimmick, designed to attract moths that think they will do a better job. Just try using them on a non conductive material, you will soon realise why. I actually gave one away a couple of days ago. As useful as a bowler hat with sleeves.

    The ones from Arc Euro do a great job.

    http://www.arceurotrade.co.uk/Catalo...t/Edge-Finders

    Bogs
    Yep, I was just trawling fleabay as I wondered how the led version worked, then I found it's only useful on conductive materials. Standard wobbler it will be then.

    Must admit I thought the led was a good idea for an awkward datum position, flap flap.:whistling:

  11. #10
    I have tried everything over the years, wigglers LED's, lasers, playboy [ but we won't go there ] and I have always gone back to the wiggler / edgefinder.

    I recently bought a pair of the ones Bogs linked to from ARC and these are my tool of choice only because I work in metric and my old bent up wiggler is still in imperial.

    I bought one of the audible and light up ones, cost me about 50 quid so for that money it has to be the best thing since sliced bread ?
    Nope, because of the brightly lit workshop and running machinery on the first edge I didn't see the light or hear the beep so that was 50 quid thrown into the bent bits scrap bin.

    Oh well another flat battery in the car park of life.
    John S -

Page 1 of 2 12 LastLast

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. wobble / wiggle on ballscrew double row angular contact bearing
    By dsc in forum Lead Screws, Nuts & Supports
    Replies: 7
    Last Post: 14-12-2013, 08:35 PM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •